Safco CS-I 150A - Spot Program Parameters in Milliseconds

CS-I User and Maintenance, R.2.8 ENG
Safco Systems Ltd-Via Isonzo 17/b-20090 Cesano Boscone-Milan-Italy
tel. +39 024504433 Fax +39 024504321 E-mail:info@safcosys.it Web site: www.safcosys.it
26 of 109
4.2.4 Spot program parameters in milliseconds
Display window
PROGRAM N° 00
Electrodes 1 (1-4)
Current NO (NO,YES)
Working Mode D‰
Limits Check NO (NO,YES)
Pressure 1 0 (0-99%)
SV Pre Squeeze NO (NO,EV1-EV4)
Pre Squeeze 0 (0-1980)
Pressure 2 0 (0-99%)
SV Squeeze NO (NO,EV1-EV4)
Squeeze 0 (0-1980)
Pressure 3 0 (0-99%)
Pre Heating time 0 (0-1980)
Pre Heating Curr. 100 (100-999‰) (D‰,V‰)
Curr. Pre Heating 1.0 (1.0-ImaxKA) (IK,EK,AD)
Pre Heating POWER 0.2 (0.2-600.0KW) (PK)
Pressure 4 0 (0-99%)
Cold time 0 10 (10-1980)
Slope-Up 0 (0-200)
Weld Time 1 1 (1-1980) (D‰,V‰,PK,IK)
ENERGY 1 10 (10-60000J) (EK)
Res.Decrem.Trsh. 0.1 (0.1-50.0%) (AD)
Weld Current 1 100 (100-999‰) (D‰,V‰)
Weld Current 1 1.0 (1.0-ImaxKA) (IK,EK,AD)
POWER Weld 1 0.2 (0.2-600.0KW) (PK)
Cold time 1 10 (10-1980)
Impulse 1 1 (1-10)
Cold time 1-2 0 (0-1980)
Weld Time 2 0 (0-1980) (D‰,V‰,IK,PK,AD)
ENERGY 2 10 (10-60000J) (EK)
Weld Current 2 100 (100-999‰) (D‰,V‰)
Weld Current 2 1.0 (1.0-ImaxKA) (IK,EK,AD)
POWER Weld 2 0.2 (0.2-600.0KW) (PK)
Cold time 2 10 (10-1980)
Impulse 2 1 (1-10)
Cold time Sald.1-2 10 (10-1980)
Impulse Weld 1-2 1 (1-10)
Slope-Dw 0 (0-200)
Cold time 3 10 (10-1980)
Temper Time 0 (0-19980)
Temper Current 100 (100-999‰) (D‰,V‰)
Temper Current 1.0 (1.0-ImaxKA) (IK,EK,PK,AD)
Temper POWER 0.2 (0.2-600.0KW) (PK)
Hold time 10 (10-1980)
Off time 0 (0-1980)
Pressure 5 0 (0-99%)
Forge NO (NO,YES)
Forge Delay 0 (0-1980)
Repeat cycle NO (NO,YES)
Initial Blanking 1 (1-200)
Curr. Max Limit 1.0 (1.0-ImaxKA) (D‰,V‰)
Curr. Min.Limit 1.0 (1.0-ImaxKA) (D‰,V‰)
Curr. Max.Limit 1 (1-30%) (IK,EK,AD)
Curr. Min.Limit 1 (1-30%) (IK,EK,AD)
P. Max. Limit 1 (1-30%) (PK)