Samsung SPD-2700 - Ssnr(Samsung Super Noise Reduction)

SPEED DOME CAMERA User’s Manual
46
SPEED DOME CAMERA User’s Manual
47
Color -> B/W B/W -> Color
Fast 2.5Lux 4Lux
Slow 0.8Lux 6Lux
Camera Setting
①Focus & Zoom
White Balance ATW
③Exposure
④Back Light OFF
AGC Medium
SSNR Medium
⑦Day & Night
⑧Others
Day & Night
①Mode COLOR
Duration FAST
③Dwell Time 0.5 SEC
Main Menu
①Camera Setting
②Sequence Setting
③P/T Setting
④OSD Setting
⑤Alarm Setting
⑥Initialize
Status
➡
➡
7. Day & Night
 ▶
Main Menu/Camera Setting/Day & Night
•TheAutomodeisdisabledwhenAGCisturnedoff.Thisfunctionisonlyavailablewhen
the Color or B/W mode is selected.
•UsingB/Wmodeundersunlightorahalogenlampmaydecreasethefocusing
performance.
Notes
The Day & Night function allows the camera to switch
between the Color and B/W modes.
Modes
:
- Auto : Operates in Color mode most times, and switches
to B/W mode if a low light level is detected during
nighttime.
- Color : Operates in Color mode at all times.
- B/W : Operates in B/W mode at all times. By using the
Burst On/Off sub menu, burst signals can be
retained or disabled.
Duration
:
The camera’s light sensitivity is adjustable as in the chart
below. The camera’s ambient light diversion performance
may vary depending on its environment.
Dwell Time
:
The duration of both the lighting conditions can be
customized to let the camera divert between the daytime
and nighttime settings.
✽ If the camera is in B/W mode and connected to equipment
that requires external sync through burst signals, set the
Burst On/Off option to “On.”
Functional Description Functional Description
Camera Setting
①Focus & Zoom
White Balance ATW
③Exposure
④Back Light OFF
AGC Medium
SSNR Medium
⑦Day & Night
⑧Others
Main Menu
①Camera Setting
②Sequence Setting
③P/T Setting
④OSD Setting
⑤Alarm Setting
⑥Initialize
Status
➡
8. Others
 ▶
Main Menu/Camera Setting/Others
Sync
: Enables selecting Internal Synchronization or the
external Line Lock. (SPD-3700T not supported)
- Internal : Synchronizes the camera’s output timing to the
internal crystal.
- Line Lock : Synchronizes the camera’s output timing to
the AC adapter power to synchronize multiple
cameras. This option is useful when using a
switch such as Matrix Switcher.
- Line Lock Phase : Enables setting the adapter’s
synchronization phase between 0 and
360°.
Stabilizer
: The Stabilizer compensates for any small
movements of the camera caused by due to
the wind and other reasonsor other causes.
Image Adj
:
- Sharpness : Sharpens outlines of an image.
- Color : Adjusts the color density of an image.
Freeze
: Stops or reanimates an image.
Dome Cover
:
These settings are to optimize the camera’s focused object
position according to the dome cover type.
- Inner : Default dome cover type including the indoor flush
model. (Factory Release Mode)
- Outer : Dome cover type for outdoor housings except the
indoor flush model.
- None : When using the camera without a dome cover.
•The Stabilizer uses the digital zoom and may cause
low picture quality.
•The Stabilizerisdisabledif theambientlightis too
low.
•TheStabilizerisdisabledifthefieldofviewhasvery
low or no contrast, e.g. The sky or a white wall.
Notes
Others
Sync INTERNAL
Stabilizer OFF
③Image Adj
Freeze OFF
Dome Cover Inner
➡