EasyManua.ls Logo

Sanus BSF316 User Manual

Sanus BSF316
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
BSF316
INSTRUCTION MANUAL
GET IT
RIGHT
THE FIRST TIME
Follow this step-by-step
instruction manual to
speed up your installation.
Para Español ver página 22
Question and Answer IconNeed help?

Do you have a question about the Sanus BSF316 and is the answer not in the manual?

Sanus BSF316 Specifications

General IconGeneral
Product TypeTV Stand
MaterialSteel
Base TypeFixed
Adjustable HeightNo
Cable ManagementYes
ColorBlack
VESA Compatibility200x200 to 600x400 mm
Compatible TV Sizes32-65 inches

Summary

Before You Begin

Remove TV Stand

Remove the TV stand if it is attached to the TV before proceeding.

Install Accessories

Install any necessary accessories before mounting the TV to the wall.

Protect TV Screen

Protect the TV screen by laying it down on a soft, clean surface during installation.

Important Safety Instructions

General Safety Precautions

Read all instructions, save them, and be aware of potential hazards.

Wall Construction and Tools

Acceptable Wall Types

Install only on wood studs or solid concrete/concrete block walls. Avoid drywall alone.

Required Tools

Lists necessary tools like tape measure, pencil, level, screwdriver, drill, etc.

Step 1: Attach TV Bracket to TV

Parts and Hardware

Lists TV screws, washers, spacers, and the TV bracket required for Step 1.

Select TV Screw Diameter

Identifies the correct screw size that fits the TV's mounting holes.

Select Screw Length and Spacers

Determines if short or long screws and spacers are needed based on TV back type.

Position and Secure Bracket

Guides on positioning the bracket on the TV and securely tightening screws.

Step 2: Attach Wall Plate to Wall

Parts and Hardware for Wall Plate

Lists drill template, lag bolts, washers, and concrete anchors for attaching the wall plate.

Step 2A: Wood Stud Installation

Locate, Verify, and Mark Stud

Instructions for finding and marking the center of a wood stud for mounting.

Position Template and Drill Holes

Guides on placing the drill template and drilling pilot holes into the stud.

Remove Wall Plate Covers

Instructions on removing the protective covers from the arm assembly.

Secure Wall Plate and Insert Covers

Tightens the wall plate with lag bolts and inserts the cover plates.

Step 2B: Solid Concrete/Block Installation

Position Template

Guides on positioning the drill template on concrete or block walls.

Drill Holes and Insert Anchors

Instructions for drilling holes and inserting concrete anchors into the wall.

Remove Wall Plate Covers

Instructions on removing the protective covers from the arm assembly.

Secure Wall Plate and Insert Covers

Tightens the wall plate with lag bolts and inserts the cover plates.

Step 3: Attach TV to Wall Plate

Parts and Hardware for TV Attachment

Lists securement screw and hex key needed to attach the TV to the wall plate.

Hang and Secure TV

Guides on hanging the TV onto the arm assembly and tightening the securement screw.

Manage Cables

Route and Attach Cable Covers

Instructions for routing cables along the arm and reattaching cable covers.

Adjustments

Level Adjustment

How to loosen, level, and tighten screws to adjust the TV's level.

Tilt Adjustment

How to adjust tilt tension knobs to ensure the TV stays in place.

Remove the TV

Steps for TV Removal

Guides on how to safely detach the TV from the wall mount.

Troubleshooting

TV Supplied Spacers

Guidance on using TV-supplied spacers for flat back or irregular back TVs.

Product Dimensions and Views

TV Interface and Wall Plate Dimensions

Provides specific measurements for the TV interface and wall plate.

Mount Views and Dimensions

Shows dimensions and views of the fully assembled mount, extended and retracted.

Product Registration

Register Your SANUS Product

Instructions and links for registering the product online for potential sweepstakes entry.

Related product manuals