Why does the weight readout change constantly on my Sartorius Scales?
The weight readout might change constantly on your Sartorius Scales due to an unstable environment, excessive vibration, a draft, or a sample that does not have a stable weight. To resolve this, try setting up the scale in another area to avoid vibration or drafts. You can also access the menu to adapt the scale to your specific weighing environment.
What to do if Sartorius G 150 D weight display shows “H”?
If the weight display on your Sartorius Scales shows “H”, it means the load exceeds the scale's capacity. Unload the scale to resolve this issue.
Why is the weight readout obviously wrong on my Sartorius Scales?
If the weight readout on your Sartorius Scales is obviously wrong, it could be due to several reasons: the scale hasn't been calibrated, it hasn't been tared before weighing, or the air bubble of the level indicator is not within the circle. To fix this, calibrate the scale, tare it before weighing, and ensure the scale is leveled properly.
How to fix the “CC“ code on my Sartorius Scales display?
If the code “CC“ remains on the display of your Sartorius Scales, it indicates that the scale is either not ready to calibrate or is in the warmup phase, or the weighing system is affected by draft or vibration. Ensure the scale warms up for at least 30 minutes after plugging it in. If the issue persists, adjust the appropriate code by accessing the operating program's menu to address any draft or vibration issues.
What to do if Sartorius Scales weight display shows “CE”?
If the weight display on your Sartorius Scales shows “CE”, it means that a zero readout was not indicated when the CAL key was pressed, or the scale is loaded. Press the tare control and re-press the CAL key to resolve this.
What to do if Sartorius G 150 D Scales weight display shows “L” or “CH2”?
If the weight display on your Sartorius Scales shows “L” or “CH2”, it indicates that the pan support and/or weighing pan is not in place. Ensure that the pan support and the weighing pan are correctly placed on the scale.
How to fix if no segments are indicated in the weight display of Sartorius G 150 D Scales?
If no segments are indicated in the weight display of your Sartorius Scales, it could be due to a lack of AC power or the AC adapter not being plugged in. Check the AC power supply and ensure the AC adapter is properly plugged in.
Choose a suitable place to set up your scale, avoiding heat, drafts, vibrations, and chemical atmospheres.
Unplug AC adapter before connecting/disconnecting peripherals to the scale's interface port.
Place the draft shield on the scale, use a screwdriver to mount it, and insert the base plate.
Ensure the AC adapter voltage matches local rating; use only original Sartorius adapters.
Select voltage only for portable power supply with European-type plug (rounded prongs).
Class 2 power supply/adapter can be plugged in without extra precautions; interface is electrically connected to scale housing.
Level the scale using feet (15) so the air bubble is centered in the level indicator (9).
Use ON/OFF key or tare control for display; scale ready after standby. Status messages explained.
Electronic circuitry test runs automatically after power-on, showing a specific final readout.
Press tare control to zero display before weighing if current reading is not zero.
Select range (W1/W2), use accessory, read display when stability symbol appears.
Hold tare control, press ON/OFF key briefly when display is off; 'CH5' appears.
Press tare control for numeral; 'L' indicates list mode (read only).
Slide switch (7) to 'C' mode; press tare control for numeral changes. 'o' shows current setting.
Slide switch (7) back; 'L' displayed. Press tare control for '0' to return.
Automatic zero tracking function (can be turned off via menu code).
Use a mild detergent wet cloth. Avoid liquid entry. Wipe dry with a soft cloth.
If safe operation is uncertain, turn off, disconnect power, notify service. Only authorized techs can repair.
General| Maximum Capacity | 150 g |
|---|---|
| Readability | 0.1 mg |
| Display | LCD |
| Linearity | ±0.2 mg |
| Repeatability | 0.1 mg |
| Interface | RS232 |
| Operating Temperature | +10°C to +30°C |
To Next Page