scheider electric MiCOM P746 - Page 75

Getting Started P746/EN GS/G31
MiCOM P746 (GS) 3-
37
1-box
Terminal 1 to 6 Terminal 1 to 6 BREAKER FAIL Opto Input 1
I>1 Function IN>1 Function Input L1
IEC S Inverse IEC S Inverse If “Indic-
CBF Control by ation” Opto Input 2
I<
V
TS Status Input L2
Blocking
I< Current Set
Opto Input 3
5.000 %
V
TS Reset Mode
Input L3
if “52a”
Manual
I>1 Current Set IN>1 Current
CB Fail 1 Timer
V
TS Time Delay
50.00 ms 5.000 s
I>1 Time Dial IN>1 Time Dial
1.000 1.000 CB Fail 2 Timer CT SUPERVISION
200.00 ms
I>1 Reset Char IN>1 Reset Char
Opto Input 32
DT DT CB Fail 3 Timer Diff CTS
Input L32
50.00 ms Enabled
I>1 tReset IN>1 tReset
if enabled
0.000 s 0.000 s CB Fail 4 Timer CTS Status
200.00 ms Blocking
if “block-
I>1 Current Set IN>1 Current I> Status ing”
Disabled CTS Time Delay
if Enabled 2.000 s
I>1 k(RI) IN>1 IDG IS I> Current Set
1.000 1.500 120.0 %
CTS I1
I>1 tReset IN>1 IDG Time 10.00
%
0.000 s 1.200 s
CTS I2/I1>1
5.000 s
CTS I2/I1>2
40.00
%
I>1 Current Set IN>1 Current
I>1 TMS IN>1 TMS
1.000 1.000
I>1 tReset IN>1 tReset
0.000 s 0.000 s
I>1 Current Set IN>1 Current
1.000 kA 200.0 A
I>1 Time Delay IN>1 Time Delay
1.000 s 1.000 s
I>1 tReset IN>1 tReset
0.000 s 0.000 s
I>2 Function IN>1 Current Set
Disabled
IN>1 k(RI)
I>2 Current Set
1.000
1.000 kA
IN>1 tReset
I>2 Time Delay 0.000 s
0.000 s
IN>2 Function
Disabled
IN>2 Current
200.0 A
V
T SUPERVISION
1.000 kA
1.000 kA
1.000 kA
200.0 A
1.000 kA
* Continue as above up
to opto Input 32
1.000 kA
EARTH FAULT
GROUP 1
CB Fail & I<
GROUP 1
SUPERVISION
GROUP 1
INPUT LABELS
GROUP 1
1.000 kA
OVERCURRENT
GROUP 1
if US ST Inverse,
US Inverse,
IEEE E Inverse,
IEEE V Inverse,
IEEEE M Inverse
if RI
if UK Rectifier,
UK LT Inverse,
IEC E Inverse,
IEC V inverse,
IEC S Inverse
if DT
if Disabled
if DT
if US ST Inverse,
US Inverse,
IEEE E Inverse,
IEEE V Inverse,
IEEEE M Inverse
if IDG
if UK Rectifier,
UK LT Inverse,
IEC E Inverse,
IEC V inverse,
IEC S Inverse
if DT
if RI
GS
if Disabled
if DT
IN>2 Time Delay
0.000 s