EasyManuals Logo

Scheppach HBS261 Translation Of The Original Instruction Manual

Scheppach HBS261
Go to English
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #33 background imageLoading...
Page #33 background image
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
33
Lower the saw band guide (4) onto the workpiece.
(8.9)
Switch on the saw.
Press one edge of the workpiece against the lon-
gitudinal fence (5) with the right hand, whilst the

Slide the workpiece at an even feed rate along the
longitudinal fence (5) into the saw band.
Important: Long workpieces must be secured
against tipping at the end of the cutting process
󰀨
Attention! When processing narrower workpieces
it is essential to use a push stick.
        
reach, on the hook (j) provided for this purpose on
the side of the saw (Fig. 17).
10.2 Angled cuts (Fig. B + 6)
In order to execute angled cuts parallel to the saw
band, it is possible to tilt the saw bench (7) for-
wards from 0° - 4.
Release the locking handle (E).
Tilt saw bench (7) forwards, until the desired angle
is set on the degree scale (I).
Retighten the locking handle (E).
Attention: With a tilted saw bench (7), the longitudi-
nal fence (5) must be positioned on the downward
facing side to the right of the saw band in the work-
ing direction (if the workpiece width allows this),
in order to secure the workpiece against slipping.
Perform the cut as described under 10.1.
10.3 Freehand cuts (Fig. C)
One of the most important features of a band saw is
the ease with which it can cut curves and radii.
Lower the saw band guide (4) onto the workpiece.
(8.9)
Switch on the saw.



with a low advancing speed, so that the saw band
can follow the desired line.




up to the front face of the curve, so that these fall
󰀨
10.4 Executing cuts with the transverse cutting
gauge (Fig. D + 18) (optional)
Set transverse cutting gauge (14) to the desired
angle (see 8.10)
Perform the cut as described under 10.1.
11. Cleaning and maintenance
Important.
      
service work disconnect the mains power plug!
General maintenance measures
    󰀨     
time using a cloth. In order to extend the service life

oil the motor.
When cleaning the plastic do not use corrosive prod-
uct.
Cleaning

housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
-


and some soft soap. Do not use cleaning agents or
solvents; these could attack the plastic parts of the
equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool i
creases the risk of an electric shock.
Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
       -


12. Storage
      
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and

         
dust and moisture.
Store the operating manual with the electrical tool.

Table of Contents

Other manuals for Scheppach HBS261

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Scheppach HBS261 and is the answer not in the manual?

Scheppach HBS261 Specifications

General IconGeneral
BrandScheppach
ModelHBS261
CategorySaw
LanguageEnglish

Related product manuals