Why is my Scheppach HS105 motor rotating in the wrong direction?
If your Scheppach Saw motor is rotating in the wrong direction, it could be due to a faulty capacitor, which requires repair by an electrical specialist. Alternatively, there might be a wrong connection. In this case, have the polarity of the outlet exchanged by a qualified electrician.
How to fix a loose saw blade on a Scheppach Saw after the motor is switched off?
If the Scheppach Saw blade is loose after the motor is switched off, it's likely because the fixing nut isn't tight enough. Tighten the fixing nut, remembering it's a right-hand thread.
Why are there fire marks on the cutting surface when using my Scheppach HS105?
Fire marks on the cutting surface when using your Scheppach Saw can occur due to a blunt or wrong saw blade. To resolve this, sharpen or change the saw blade.
What to do if my Scheppach HS105 engine will not start?
If your Scheppach Saw engine won't start, it could be due to several reasons. First, check the mains fuse and replace it if necessary. If the fuse is fine, the extension cable might be defective, requiring a replacement. In other cases, the connections on the motor or switch may not be in order, or the motor or switch itself might be faulty, both of which require repair by an electrical specialist.
Why does my Scheppach Saw leave burns on the cutting surface?
If you're experiencing burns on the cutting surface of your Scheppach Saw, it could be due to several reasons. Ensure you're using a sharpened saw blade. For longitudinal cuts, use a saw blade with 20 or 28 teeth. Also, check that the longitudinal stop and slide carriage are parallel to the saw blade; if not, adjust or exchange the longitudinal stop and align the slide carriage.
What to do if my Scheppach HS105 motor turns off automatically?
If your Scheppach Saw has no motor output and turns off automatically, it's likely due to an overload caused by a dull saw blade, which triggers the thermoprotection. To resolve this, insert a sharpened saw blade. After the motor cools down, you can turn it on again.
Why won't my Scheppach Saw motor start?
If your Scheppach Saw motor isn't starting, first check the mains fuse. If that's not the issue, the extension cable might be defective; consult the operating manual's “Electrical Connection” section for guidance. Lastly, there could be defective connections on the motor or switch, in which case you should have an electrician check it.
How to prevent burnt areas on the cutting surface with my Scheppach HS105?
Burnt areas on the cutting surface when using the Scheppach Saw can occur due to: * A blunt saw blade. Sharpen or replace the saw blade. * Using the incorrect saw blade. Replace the saw blade with the correct one.
How to fix a Scheppach HS105 Saw when the saw blade gets loose?
If the saw blade on your Scheppach Saw gets loose after turning off the motor, tighten the fastening nut, remember it has an M20 left-handed thread.
How to fix a loose saw blade on my Scheppach HS105 after turning off the motor?
If the saw blade gets loose after turning off the motor, the fastening nut may not be tightened sufficiently. Ensure you tighten the fastening nut, which has an M20 left-handed thread.
Provides essential safety guidelines for operating power tools.
Ensures a safe operating environment by maintaining cleanliness and proper lighting.
Details precautions for safe electrical connections and usage.
Emphasizes operator alertness, protective equipment, and proper attire.
Highlights dangers and precautions during various cutting operations.
Explains kickback phenomena and preventive safety measures.
Rules for safe operation, placement, and handling of table saws.
Guidelines for safe installation, removal, and use of saw blades.
General| Product color | Blue, White |
|---|---|
| Built-in light | No |
| Country of origin | Germany |
| Suitable for materials | Wood |
| Saw blade included | Yes |
| Input power | 2000 W |
| Power source | AC |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Blade diameter | 255 mm |
| Number of teeth | 60 |
| Idle speed (max) | 7000 RPM |
| Bevel capacity (max) | 45 ° |
| Cutting depth (45º) | 50 mm |
| Cutting depth (90º) | 80 mm |
Weight and Dimensions| Depth | 760 mm |
|---|---|
| Width | 690 mm |
| Height | 380 mm |
| Weight | 30500 g |
To Next Page
