www.scheppach.com
GB
|
31
Other general occupational health and safety-related
rules and regulations must be observed.
m ATTENTION
When using the product, several safety warnings
must be observed to prevent injuries and damage.
For this reason, carefully read the operating and safe-
ty instructions. Keep them in a safe place so that the
information is available at all times. If the product is
handed over to another person, hand over the op-
erating and safety instructions with it. We accept no
liability for accidents or damage that occur due to
a failure to observe this operating manual and the
safety instructions.
The liability of the manufacturer and resulting dam-
ages are excluded in the event of modications of
the machine.
Despite use as intended, specic risk factors cannot
be entirely eliminated. Due to the design and layout
of the machine, the following risks remain:
• Contact with the saw blade in the exposed sawing
area.
• Reaching into the running saw blade (cutting injury)
• Kick-back of workpieces and workpiece parts
• Saw blade breakage
• Ejection of faulty carbide parts of the saw blade
• Hearing damage when the necessary hearing pro-
tection is not used.
• Harmful emissions of wood dusts during use in en-
closed areas.
6. Safety information
General power tool safety warnings
m WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.
Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
Save all warnings and instructions for future ref-
erence.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive at-
mospheres, such as in the presence of am-
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
28. Guide rail
4. Scope of delivery
• Operating manual
• Saw blade 24 teeth (pre-mounted)
• Saw blade guard
• Parallel stop (incl. stop rail − pre-mounted)
• Transverse stop (incl. stop rail − pre-mounted)
• Table width extension (2x)
• Push stick
• Legs (4x)
• Transverse struts (2x)
• Longitudinal struts (2x)
• Rubber feet (4x)
• Table support short (2x)
• Table support medium (2x)
• Scale
Assembly material
a. Hexagon screw M6x12, washer, nut M6 (8x)
b. Hexagon screw M6x30, washer (6x)
c. Philips screw M6x30, washer (2x)
d. Coach bolt M6x12, washer, nut M6 (16x)
e. Slotted-head screw M4x6 (2x)
f. Open-ended spanner 22 mm (2x)
g. Open-ended spanner 8/10 mm
h. Allen key 5 mm
5. Proper use
The circular table saw is used for the longitudinal and
transverse cutting (only with the transverse stop) of
all types of timbers and plastic, in accordance with
the machine size. It is not permitted to cut any type
of round timber.
Only suitable saw blades (HM or CV saw blades) may
be used for the machine. The use of HSS saw blades
and any type of cutting wheels is prohibited.
Notes:
Compliance with the regulations, safety instructions,
descriptions and notes in this operating manual are
part of proper use.
The safety, operating and maintenance specications
of the manufacturer, as well as the dimensions speci-
ed in the operating manual, must be observed.
Working on or with the product may only be carried
out as described in this operating manual. All other
maintenance and repair work not described in this
operating manual must be carried out by a customer
service centre.
Please observe that our equipment was not designed
with the intention of use for commercial or industrial
purposes. We assume no guarantee if the equipment
is used in commercial or industrial applications, or for
equivalent work.
To Next Page
Loading...
