www.scheppach.com
36
|
GB
• Remove the packaging material, packaging and
transport safety devices (if applicable)..
• Check the completeness of the scope of delivery.
The customer service must be notied immediately
of any complaints. Later claims will not be recog-
nised.
• Check the scope of delivery for transport damage.
The transport company must be notied immediate-
ly of any complaints. Later claims will not be recog-
nised.
• Keep the packaging until the end of the warranty
period.
• Read through the operating manual completely.
• Only use original spare parts or accessories. Origi-
nal spare parts or accessories can be obtained from
your dealer.
• Check that the data on the type plate matches with
the mains power data.
9. Assembly
m WARNING: Remove the mains plug before main-
taining, modifying or assembling the circular table
saw.
m Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
1x open-ended spanner 8/10 mm (g)
1x Allen key 5 mm (h)
(included in the scope of delivery)
1x Phillips screwdriver
1x slotted-head screwdriver
(not included in the scope of delivery)
• Place all supplied parts on a at surface.
• Group equal parts.
NOTE:
• If connections are secured with a screw (round-
head or hexagon), hexagon nuts and washers, the
washer must be tted under the nut.
• Insert screws each from outside to inside. Secure
connections with nuts on the inside.
• Tighten the nuts and screws during assembly only
until they are unable to fall o. If you tighten the nuts
and screws fully before nal assembly, it is not pos-
sible to complete the assembly.
9.1 Table width extensions
Before assembling the table width extensions, you
must pre-mount the legs of the base frame.
9.1.1 Pre-mounting the legs of the base frame
(g. 4)
1. Turn the saw table (2) over and place it on the
oor.
Noise
The noise values have been determined in accord-
ance with EN 62841.
Sound pressure level L
pA
........................... 96,8 dB(A)
Uncertainty K
pA
.................................................... 3 dB
Sound power level L
WA
............................. 109,8 dB(A)
Uncertainty K
WA
.................................................... 3 dB
m WARNING
Excessive and frequent exposure to noise can lead to
hearing damage or hearing loss.
- Wear hearing protection
- Take breaks.
Total vibration values (vector sum of three directions)
determined according to EN 62841.
NOTE: The specied noise emission values have
been measured in accordance with a standardised
test procedure and can be used to compare one
power tool with another.
The specied noise emission values can also be used
for an initial estimation of the exposure.
WARNING: The noise emission values can vary from
the specied values during the actual use of the power
tool, depending on the type and the manner in which
the power tool is used, and in particular the type of
workpiece being processed.
Implement measures to protect against noise nui-
sance.
In doing so, take into account the complete working
process, including the times when the power tool is
working without load or switched o. Suitable meas-
ures include regular maintenance and care of the
power tool and the insertion tools, regular breaks as
well as proper planning of the working process.
It is necessary to dene safety measures to protect
the operator which are based on an estimate of vibra-
tion exposure during the actual operating conditions
(for this, all parts of the operating cycle have to be
considered, e.g. times during which the power tool is
switched o and times during which it is switched on
but runs in no-load mode).
8. Unpacking
Danger of choking or suocating
The packaging material, packaging and transport
safety devices are not children‘s toys. Plastic bags,
foils and small parts can be swallowed and lead to
choking.
- Keep packaging material, packaging and trans-
port safety devices away from children.
• Open the packaging and carefully remove the prod-
uct.
To Next Page
Loading...
