Schwinn 590e - User Manual

Questions and Answers

K
Kenneth MillsAug 19, 2025
Why Schwinn 590e Elliptical Trainer display is not working?
- K
  Katherine MirandaAug 19, 2025
  If your Schwinn Elliptical Trainer's display isn't working, it could be due to several reasons. First, ensure the unit is plugged into a functioning wall outlet. Check the power cord and inlet for any damage, replacing them if necessary. Inspect the wires in the cable for pinches or cuts, and replace the cable if any are found. Make sure the cables at the base of the mast and the back of the console are securely connected and properly oriented, ensuring the small latch on the connector snaps into place. Check the console display for cracks or damage, and replace the console if damaged. If the console only shows a partial display and all connections are fine, consider replacing the console.
A
Ashley TorresAug 21, 2025
What to do if my Schwinn 590e Elliptical Trainer console shuts off during use?
- N
  Nancy HobbsAug 21, 2025
  If your Schwinn Elliptical Trainer console shuts off during use, ensure the unit is plugged into a functioning wall outlet and the connection is secure and undamaged. Replace the cord or power inlet if damaged. Check all wires in the cable for cuts or pinches, replacing the cable if necessary. Make sure the cable is connected securely and oriented properly, with the small latch on the connector lined up and snapped into place. Try unplugging the unit from the electrical outlet for 3 minutes, then reconnect it. Also, verify that the magnet is in place on the pulley and that the speed sensor is aligned with the magnet and connected to the data cable. Realign the sensor if necessary, and replace it if there's any damage to the sensor or the connecting wire.
F
Francisco HermanAug 25, 2025
How to fix Schwinn 590e resistance if it does not change?
- D
  Daniel JamesAug 25, 2025
  If the resistance on your Schwinn Elliptical Trainer isn't changing, check that all wires in the cable are intact and replace the cable if you find any pinches or cuts. Ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. If these steps don't work, the Servo Motor may need replacement. Also, check the console display for any signs of damage, and replace it if necessary. Ensure the cable from the right Upper Handlebar and cables to the Console are secure and undamaged.
S
Sean MitchellAug 26, 2025
How to troubleshoot Bluetooth heart rate not displayed on Schwinn 590e Elliptical Trainer?
- J
  Julie WillisAug 26, 2025
  If the Bluetooth Heart Rate (HR) isn't displayed on your Schwinn Elliptical Trainer, follow the troubleshooting instructions provided with the HR device. If the monitor uses replaceable batteries, install new ones. Try moving the unit away from sources of interference like TVs or microwaves. During a workout, only push the On/Off LED button once to activate the armband. If eliminating interference doesn't resolve the issue, replace the HR device.
M
mchurchAug 28, 2025
How to stop knocking sound during Schwinn 590e Elliptical Trainer operation?
- K
  Kevin GarciaAug 28, 2025
  To stop a knocking sound during your Schwinn Elliptical Trainer operation, make sure that the alignment tab on the Pivot Sleeve goes into the slot in the hole and that the Pivot Sleeve extends through the opposite hole in the joint cover.
D
Desiree SimmonsAug 30, 2025
How to resolve squeaking noise on Schwinn Elliptical Trainer?
- B
  Brianna HooperAug 30, 2025
  To address a squeaking noise on your Schwinn Elliptical Trainer that appears a few minutes into a workout and gets progressively worse, try loosening the pivot rod bolts slightly until the noise goes away. You can also apply silicone lubricant to a dry cloth and wipe the rails to eliminate roller noise.
K
Kyle CarterSep 1, 2025
How to fix Schwinn Elliptical Trainer incline if it does not adjust?
- L
  lindahurleySep 1, 2025
  If the incline on your Schwinn Elliptical Trainer isn't adjusting, first, ensure the cable is connected securely and oriented properly, making sure the small latch on the connector lines up and snaps into place. Check the console display for any signs of damage, and replace it if necessary. Also, be sure the cable from the left Upper Handlebar and cables to the Console are secure and undamaged. Verify that the Incline Adjuster Assembly is attached to the Incline Motor drive screw. Note that additional incline adjustments may be disabled for a few minutes to protect the motor from overheating; allow the lift motor to cool before resuming your workout.
V
Vincent JohnsonSep 3, 2025
Why Schwinn Elliptical Trainer has no speed or RPM reading?
- A
  Albert GrahamSep 3, 2025
  If your Schwinn Elliptical Trainer isn't displaying speed or RPM readings, ensure all wires in the cable are intact, replacing the cable if any are cut or pinched. Check that each cable is connected securely and oriented properly, ensuring the small latch on the connector lines up and snaps into place. Verify that the magnet is in place on the pulley. Also, make sure the speed sensor is aligned with the magnet and connected to the data cable; realign the sensor if necessary, and replace it if there's any damage to the sensor or the connecting wire.
G
Gerald BarronSep 5, 2025
What to do if Schwinn 590e Elliptical Trainer unit rocks or isn't level?
- M
  Mr. Anthony ReedSep 5, 2025
  If your Schwinn Elliptical Trainer rocks or doesn't sit level, adjust the levelers until the machine is stable. Keep in mind that adjustments may not fully compensate for extremely uneven surfaces, so consider moving the machine to a more level area.
J
jasmine99Sep 7, 2025
How to fix Schwinn 590e pedals if they are loose or the unit is difficult to operate?
- D
  Danielle WatsonSep 7, 2025
  If the pedals on your Schwinn Elliptical Trainer are loose or the unit is difficult to operate, tightly secure all hardware on the Pedals, Legs, and Handlebar Arms.