Selve i-R Timer Plus - User Manual

Questions and Answers

M
morrisbrittanyAug 16, 2025
Why is the Astro programme not functioning correctly on my Selve Timer?
- M
  matthewjohnsonAug 16, 2025
  If the Astro programme on your Selve Timer isn't working according to the set switching times, it might be due to several reasons. First, ensure that the date is correctly set. Second, verify that the correct city or exact latitude/longitude is set. Third, check if the holiday function is activated and, if so, deactivate it. Finally, examine if the astro shift is set and adjust it as needed.
A
Angela MartinAug 19, 2025
What to do if Selve i-R Timer Plus does not carry out the switching commands?
- B
  Bryan BrownAug 19, 2025
  If your Selve i-R Timer Plus isn't executing switching commands, the sliding switch may be set to manual. To resolve this, move the sliding switch to the automatic position.
C
Carlos RobertsAug 22, 2025
Why is the transmission control light flashing on my Selve Timer?
- A
  Adam SanchezAug 22, 2025
  If the transmission control light on your Selve Timer is flashing, it indicates that the batteries are running low. To fix this, insert new batteries.
I
imendezAug 26, 2025
What to do if Selve Timer drive is not functioning and transmission control light is lit?
- K
  Kimberly WongAug 26, 2025
  If the drive isn't functioning and the transmission control light is lit on your Selve Timer, it could be due to the receiver being outside the radio range. Try reducing the distance to the receiver. Alternatively, the transmitter may not be programmed in the receiver, in which case you should program the transmitter.
M
Matthew BrownAug 28, 2025
Why Selve i-R Timer Plus does not carry out the switching commands precisely?
- S
  Stephen EdwardsAug 28, 2025
  If your Selve i-R Timer Plus isn't performing switching commands precisely, it's possible that the holiday function is activated. Turn off the holiday function to ensure accurate switching.
C
Christine MendozaAug 31, 2025
How to fix a Selve Timer drive that is not functioning?
- J
  Julie CopelandAug 31, 2025
  If the drive on your Selve Timer is not functioning, it may be due to a faulty connection. Check the connection to ensure it is properly established.
D
David MarshallSep 3, 2025
What to do if the Selve Timer transmitter does not react after the batteries have been changed?
- M
  Michael PearsonSep 3, 2025
  If your Selve Timer's transmitter isn't reacting after you've changed the batteries, it might be because the power supply was interrupted for too long. Press the RESET button and then check your settings.
M
Michael KimSep 6, 2025
Why Selve Timer drive is not functioning, transmission control light is not lit?
- K
  Kim ThompsonSep 6, 2025
  If the drive isn't functioning and the transmission control light isn't lit on your Selve Timer, it indicates that the batteries are dead or incorrectly inserted. Insert new batteries, ensuring they are correctly oriented.
J
Jo WallaceSep 9, 2025
What to do if the sun and twilight parameters cannot be changed on Selve i-R Plus Timer?
- R
  racheldurhamSep 9, 2025
  If the sun and twilight parameters cannot be changed or are not displayed on your Selve Timer, it indicates that either no light sensor is connected, or the light sensor and/or the connecting cable is faulty. Check the light sensor, connecting cable, and connector plug.
M
Maria NorrisSep 12, 2025
Why Venetian blind or roller shutter does not move to the end limit on Selve i-R Plus Timer?
- S
  Scott TorresSep 12, 2025
  If your Venetian blind or roller shutter does not move to the end limit with your Selve Timer, no end limit position is set. Set the end limit position using the setting menu PROG 1/2.

Selve i-R Timer Plus Specifications

General

Operating Voltage	230 V AC
Protection Class	IP20
Mounting	Flush-mounted
Radio Frequency	868 MHz
Number of channels	1
Display	LCD
Battery backup	Yes
Weight	150 g
Type	Timer

Selve i-R Timer Plus - User Manual

Table of Contents

Questions and Answers

Selve i-R Timer Plus Specifications