Shark 100 - Page 4

To Next Page

To Previous Page

Doc# E145701 ii

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

This page intentionally left blank.

Main Page

Product Warranty5
Use of Product for Protection6
Statement of Calibration6
Disclaimer6
Table of Contents9
1: Three-Phase Power Measurement15
Three-Phase System Configurations15
1: Wye Connection15
2: Delta Connection18
3: Blondel's Theorem and Three Phase Measurement20
Power, Energy and Demand22
Reactive Energy and Power Factor26
Harmonic Distortion28
Power Quality31
2: Meter Overview and Specifications33
Hardware Overview33
1: Voltage and Current Inputs35
2: Model Number Plus Option Numbers36
Technology38
4: Measured Values40
5: Utility Peak Demand41
Specifications41
Compliance47
Accuracy48
3: Mechanical Installation51
Introduction51
ANSI Installation Steps54
DIN Installation Steps55
Shark® 100T Transducer Installation56
4: Electrical Installation59
Considerations When Installing Meters59
CT Leads Terminated to Meter62
CT Leads Pass through (no Meter Termination)63
Quick Connect Crimp-On Terminations64
Voltage and Power Supply Connections65
Ground Connections65
Voltage Fuses65
Electrical Connection Diagrams66
Extended Surge Protection for Substation Instrumentation79
5: Communication Installation81
2: RS485/KYZ Output Com 2 (485P Option)81
1: Using the Unicom 250085
Electro Industries/Gaugetech Doc TOC86
Configuring the Shark® 100 - INP1086
1: Setting up the Host PC to Communicate with the Shark® 100 - INP10 Meter87
1: Configuring the Host Pc's Ethernet Adapter through87
Windows87
2: Setting up the Shark® 100 - INP10 Meter for Ethernet Communication89
1: Configuring the Shark® 100 - INP10 Meter's90
2: Resetting the Ethernet Card (INP10)92
Shark® 100B Meter Ethernet Configuration92
6: Using the Shark® 100/50 Meter93
Programming the Shark® 100/100B/50 Meter Using the Faceplate93
1: Understanding Meter Face Elements93
2: Understanding Meter Face Buttons94
Using the Front Panel95
1: Understanding Startup and Default Displays95
2: Using the Main Menu96
3: Using Reset Mode97
4: Entering a Password98
5: Using Configuration Mode99
1: Configuring the Scroll Feature101
2: Configuring CT Setting102
Electro Industries/Gaugetech Doc TOC102
3: Configuring PT Setting103
4: Configuring Connection Setting105
5: Configuring Communication Port Setting105
6: Using Operating Mode107
Understanding the % of Load Bar108
Performing Watt-Hour Accuracy Testing (Verification)109
Programming the Transducer or Meter Using Software111
1: Accessing the Transducer/Meter in Default111
2: Connecting to the Transducer/Meter through112
TM Software112
Irda Port (Com 1)115
3: Device Profile Settings116
Display Configuration120
7: Using the Shark® 100B Meter125
Introduction125
1: about Bacnet125
Shark® 100B Meter's Bacnet Objects126
Configuring the Shark® 100B Meter129
Using the Shark® 100B Meter's Web Interface136
Using the Shark® 100B in a Bacnet Application142
A: Shark® 100/50 Meter Navigation Maps143
A.1: Introduction143
A.2: Navigation Maps (Sheets 1 to 4)143
B: Shark® 100 and 50 Meter Modbus Map149
B.1: Introduction149
B.2: Modbus Register Map Sections149
B.3: Data Formats149
B.4: Floating Point Values150
B.5: Modbus Register Map151
C: Shark® 100 Meter DNP Map169
C.1: Introduction169
C.2: DNP Mapping (DNP-1 to DNP-2169
D: DNP 3.0 Protocol Assignments173
D.1: DNP Implementation173
D.2: Data Link Layer174
D.3: Transport Layer175
D.4: Application Layer175
D.4.1: Object and Variation176
D.4.1.1: Binary Output Status (Obj. 10, Var. 2177
D.4.1.2: Control Relay Output Block (Obj. 12, Var. 1178
D.4.1.3: 32-Bit Binary Counter Without Flag (Obj. 20, Var. 5179
D.4.1.4: 16-Bit Analog Input Without Flag (Obj. 30, Var. 4179
D.4.1.5: Class 0 Data (Obj. 60, Var. 1185
D.4.1.6: Internal Indications (Obj. 80, Var. 1185
E: Using the USB to Irda Adapter CAB6490187
E.1: Introduction187
E.2: Installation Procedures187

Shark 100 - Page 4

Table of Contents

Related product manuals