Sharp AQUOS LC-40LE924RU

13
Initial auto installation
WhentheTVispoweredonforthefirsttimeafter
purchase,theinitialautoinstallationwizardappears.
Followthemenusandmakethenecessarysettingsone
afteranother.
Confirm the following before turning on
the power
E Istheantennacableconnected?
E IstheACcordpluggedin?
E IstheMAINPOWERswitchturnedon(;)?
1 Press <a on the TV.
• Theinitialautoinstallationwizardappears.
2 Setting the OSD language.
Pressa/b/c/dtoselectthedesiredlanguage,
andthenpress;.
3 Selecting the location of the TV.
HOME
STORE
Pressc/dtoselectwhereyouwillusethisTV,
andthenpress;.
• Theconfirmationscreenpopsuponlywhenselecting
“STORE”.Pressc/dtoselect“Yes”or“No”.
• HOME:“STANDARD”willbethedefaultvalueforthe“AV
mode”setting.
• STORE:“DYNAMIC(Fixed)”willbethedefaultvaluefor
the“AVmode”setting.Ifthe“AVmode”ischanged,the
TVwillautomaticallyswitchbackto“DYNAMIC(Fixed)”
whenthereisnosignalinputfromtheTVorremote
controlunitfor30minutes.
• STORE:Ademonstrationimagewillbedisplayedafter
initialautoinstallationiscompleted.Ifyouhavechosen
“STORE”bymistake,goto“Setup”>“Viewsetting”>
“Reset”>select“HOME”again.
4 Setting the country.
Pressa/b/c/dtoselectyourcountryorarea,
andthenpress;.
• Thissettingscreenonlyappearsduringthefirst
installation.
NOTE
• Ifyouset“Sweden”inthecountrysetting,youcanselect
thecableprovider“ComHem”.RefertotheHmark
inthefollowingstepsorinstructionsaboutthesettingsfor
“ComHem”.
5 Starting channel search.
Digital search
Analogue search
Skip
Pressa/btoselect“Digitalsearch”,“Analogue
search”or“Skip”,andthenpress;.
• Towatchbothanaloguebroadcasts,digitalbroadcasts
andsatellitebroadcasts,youshouldperformtheauto
installationsettingforeachformat(Page34).
• Ifyouwanttosearchformorebroadcasts,execute
“Additionalsearch”fromthe“Programmesetup”menu
(Pages34_36).
• Whenyouselect“Skip”,only“Satellitesearch”willbe
performed.Youshouldperform“Digitalsearch”and
“Analoguesearch”from“Autoinstallation”underthe
“Setup”menuifneeded.
• Afterperforming“Digitalsearch”or“Analoguesearch”,
thescreenswicthestothe“Satellitesearch”setting.You
shouldthenexecute“Yes”ifyouwanttosearchforthe
satellitechannels.
NOTE
• IfyouturnoffthepowerontheTVwhileperformingachannel
search,theinitialautoinstallationwizardwillnotappear.The
autoinstallationfunctionallowsyoutoexecutetheinstallation
againfrom“Setup”>“Viewsetting”(Page34).
• TheinitialautoinstallationwizardwillabortifyouleavetheTV
unattendedfor30minutesbeforesearchingforchannels.
• Afterinitialautoinstallationiscompleted,thedefaultPINis
automaticallysetto“1234”.TochangethePINsetting,refer
toPassword/Lock settings(Page37).ToclearthePINsetting
(PINinputwillnolongerbeneeded),refertoCLEARING THE
PIN(Page59).
• When“Italy”isselectedinthecountrysetting,thedefaultage
restrictionvalueissetto18.
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”,
and then press ;.
Terrestrial
Cable
H
• Whenyouset“Sweden”inthecountrysettingandselect
“Cable”forthesearchingformat,youcanselectthe
cableprovider“ComHem”.
E Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
• Toaborttheinitialautoinstallationinprogress,press6.
After searching for DVB-T channels, the
screen switches to the “Satellite search”
setting (Page 15).
Quick guide