Sharp MX-5001N - Page 84

MX-5001N ADJUSTMENTS 5 – 42
SIM50-6
(DSPF)
(RSPF)
* Item A, B: When the adjustment value is increased, the scan
timing is delayed.
* * Item C - H: When the adjustment value is increased, the
image loss is increased.
* * Item A - H: 1 step = 0.1mm change
* The SPF rear edge image loss is provided for countermea-
sures against shades.
6) Select an adjustment item with the scroll key.
(SIM48-1)
(SIM50-6)
7) Enter an image magnification ratio adjustment value with 10-
key, and press [OK] key.
When the adjustment value is increased, the image magnifica-
tion ratio is increased.
When the adjustment value is changed by 1, the image magni-
fication ratio is changed by 0.01%.
Repeat the procedures of 1) - 7) until a satisfactory result is
obtained.
NOTE: When [CLOSE] key is pressed in this simulation mode, the
machine goes into the normal operation mode. Under this
state, copy check can be normally performed. When the
system key is pressed, the machine returns to the simula-
tion mode.
Item Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment
(CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment
(CCD)
1 - 99 50
C Image
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface
lead edge image
loss amount
setting
0 - 99 20
D FRONT_REAR
(SIDE1)
Front surface
side image loss
amount setting
0 - 99 20
E TRAIL_EDGE
(SIDE1)
Front surface
rear edge image
loss amount
setting
0 - 99 30
F Image
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
Back surface
lead edge image
loss amount
setting
0 - 99 30
G FRONT_REAR
(SIDE2)
Back surface
side image loss
amount setting
0 - 99 20
H TRAIL_EDGE
(SIDE2)
Back surface
rear edge image
loss amount
setting
0 - 99 20
I OFSET_SPF1 DSPF front
surface
document off-
center
adjustment
1 - 99 50
J OFSET_SPF2 DSPF back
surface
document off-
center
adjustment
1 - 99 50
K SCAN_SPEED_SPF1 DRSPF
document front
surface
magnification
ratio adjustment
(Sub scan)
1 - 99 50
Item Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment
(CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment
(CCD)
1 - 99 50
C Image
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface
lead edge image
loss amount
setting
0 - 99 20
D FRONT_REAR
(SIDE1)
Front surface
side image loss
amount setting
0 - 99 20
E TRAIL_EDGE
(SIDE1)
Front surface
rear edge image
loss amount
setting
0 - 99 30
FImage
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
Back surface
lead edge image
loss amount
setting
0 - 99 20
G FRONT_REAR
(SIDE2)
Back surface
side image loss
amount setting
0 - 99 20
H TRAIL_EDGE
(SIDE2)
Back surface
rear edge image
loss amount
setting
0 - 99 30
I OFSET_SPF1 RSPF front
surface
document off-
center
adjustment
1 - 99 50
J OFSET_SPF2 RSPF back
surface
document off-
center
adjustment
1 - 99 50
K SCAN_SPEED_SPF1 RSPF document
front surface
magnification
ratio adjustment
(Sub scan)
1 - 99 50
L SCAN_SPEED_SPF2 RSPF document
back surface
magnification
ratio adjustment
(Sub scan)
1 - 99 50
SPF (SUB) Sub scanning direction image magnification ratio (Front
surface)
SPFB (SUB) Sub scanning direction image magnification ratio (Back
surface)
SCAN SPEED SPF1 Sub scanning direction image magnification
ratio (Front surface)
SCAN SPEED SPF2 Sub scanning direction image magnification
ratio (Back surface)
Item Display Content
Setting
range
Default
value