How to troubleshoot a Sherwood Receiver with no power?
If your Sherwood Receiver has no power, there are a couple of things you can check. First, ensure that the AC input cord is securely connected. If it is, then verify that the AC wall outlet is working by testing it with a lamp or another appliance. It's possible the outlet is inactive or has a poor connection.
Why is there no sound coming from my Sherwood RD-6108?
If you're not getting any sound from your Sherwood Receiver, here are some things to check: * Make sure the speaker cords are properly connected. * Adjust the master volume to an audible level. * Ensure the MUTE button on the remote is not activated. * Verify that the speakers are switched on by pressing the SPEAKER button. * Select the correct input source. * Confirm that all components are connected correctly.
What to do if the Sherwood Receiver remote control is not working?
If the remote control for your Sherwood Receiver isn't working, first, replace the batteries. If that doesn't solve the issue, make sure nothing is obstructing the remote sensor on the receiver.
How to fix Sherwood RD-6108 Receiver when it cannot receive stations?
If your Sherwood Receiver isn't picking up any stations, make sure an antenna is connected. Then, tune in the desired station frequency. Finally, try moving the antenna to a different position and retry tuning.
How to improve poor FM reception on Sherwood RD-6108 Receiver?
If you're experiencing poor FM reception on your Sherwood Receiver, first ensure that an antenna is connected. If an antenna is connected, try changing its position to improve reception.
Why is there no sound from the rear speakers on my Sherwood Receiver?
If you're not hearing sound from the rear speakers on your Sherwood Receiver, check these things. Ensure that a surround mode is selected instead of stereo mode. Adjust both the master volume and the rear level to appropriate settings. Make sure you're using a stereo or surround source, not a monaural one. Also, verify that the rear speaker setting is correctly configured and not set to “N”.
What to do if Sherwood RD-6108 Receiver has no sound from the center speaker?
If there's no sound coming from the center speaker of your Sherwood Receiver, first, check that you've selected a surround mode and not stereo mode. Next, make sure the center speaker setting isn't set to “N”. Finally, adjust the master volume and center level to ensure they're not too low.
Why can't my Sherwood RD-6108 receive preset stations?
If your Sherwood Receiver isn't receiving preset stations, it could be due to an incorrect station frequency being memorized. In this case, memorize the correct station frequency. It's also possible the memorized stations were cleared, so try memorizing the stations again.
How to stop continuous hissing noise during FM reception on Sherwood Receiver?
If you're experiencing a continuous hissing noise during FM reception on your Sherwood Receiver, especially with stereo broadcasts, it could be due to weak signals. Try changing the position of the antenna. Consider installing an outdoor antenna.
What causes continuous hissing noise during AM reception on Sherwood RD-6108?
If you're hearing continuous or intermittent hissing noise during AM reception on your Sherwood Receiver, especially at night, it's likely due to interference from motors, fluorescent lamps, or lightning. Try keeping the receiver away from these noise sources. Consider installing an outdoor AM antenna.
Amplifier Section| power output, stereo mode | 2 x 100 W |
|---|---|
| total harmonic distortion | 0.09% |
| intermodulation distortion | 0.1% |
| input sensitivity | 200 mV |
| signal to noise ratio | 92 dB |
| frequency response | +0 dB, -3 dB |
| output level | 200 mV |
| pre out | 1.0 V |
| bass/treble control | +10 dB |
| front power output | 125 W+125 W |
| center power output | 125 W |
| rear power output | 125 W+125 W |
Digital Audio Section| sampling frequency | 32, 44.1, 48, 96 kHz |
|---|---|
| digital input level, coaxial | 0.5 Vp-p |
| digital input level, optical | -15_-21 dBm |
FM Tuner Section| tuning frequency range | 87.5~108 MHz |
|---|---|
| usable sensitivity | 12.8 dBf |
| 50 dB quieting sensitivity, mono/stereo | 20.2/45.3 dBf |
| signal to noise ratio, mono/stereo | 70/65 dB |
| total harmonic distortion, mono/stereo | 0.5/0.8% |
| frequency response | --+3dB |
| stereo separation | 42 dB |
| capture ratio | 4 dB |
| IF rejection ratio | 80 dB |
AM Tuner Section| tuning frequency range | 520_1710 kHz |
|---|---|
| usable sensitivity | 500/zV/m |
| signal to noise ratio | 40 dB |
| selectivity | 25 dB |
General| power supply | AC 120 V, 60 Hz |
|---|---|
| power consumption | 200 W |
| dimensions | 440 × 141 × 330 mm |
| weight | 9.6 kg |
To Next Page
