To Next Page
J
josephjonesSep 9, 2025
What to do if my Shimaden Controller is in trouble?
- JJohn JonesSep 9, 2025
Examine, repair or replace the product.
What to do if my Shimaden Controller is in trouble?
Examine, repair or replace the product.
Why does the displayed PV value seem incorrect on my Shimaden Controller?
If the displayed PV value seems incorrect on your Shimaden Controller, there are a couple of potential reasons: * The set measuring range code might differ from that of the input sensor or signal. To resolve this, check and ensure that the set measuring range code is correct for the input signal. * There may be erroneous wiring to the input terminals of the sensor. In this case, correct the wiring to the input terminals.
What to do if a key is unable to be operated on Shimaden Controller?
If you find that a key on your Shimaden Controller is not working, consider these possibilities: 1. The keylock function may be enabled. Try releasing the keylock. 2. The product might be deteriorating. In this case, examine the controller and repair or replace it if necessary. 3. If the communication function is active, the controller might be in communication mode (Com). Change the communication setting to the local mode (Loc).
Why does the display go out on my Shimaden Controller and it does not operate?
If the display on the front panel of your Shimaden Controller goes out and the instrument stops operating, here are a few things to check: * There may be a problem with the power supply or wiring connection. Inspect all power-related components and wiring, and ensure everything is correctly connected. * The product itself might be deteriorating. In this case, examine the controller and consider repairing or replacing it.
How to fix too fast ON-OFF action of control output on Shimaden Controller?
If the ON-OFF action of the control output on your Shimaden Controller is too fast: * It's possible that ON-OFF is set for the proportional (P) element of PID control. Change the OFF setting for P to a two-position type ON-OFF action. * The hysteresis value for the ON-OFF action might be too small. Try increasing the hysteresis value.
Specifies suitable and unsuitable environmental conditions for instrument installation.
Detailed instructions and precautions for wiring the instrument and its components.
Illustrates the terminal layout for different SR90 series models for wiring reference.
A table detailing terminal names, descriptions, and corresponding numbers for wiring.
Step-by-step guide for initial checks and settings before operating the controller.
Visual representation of the screen navigation and parameter setting flow.
Detailed steps for setting parameters within Screen Group 0.
Procedure for setting the target set value (SV) using the basic screen.
Steps for switching to manual mode and setting control output values.
Explains execution, stopping, unexecutable conditions, and automatic stop of auto-tuning.
Explains standby mode, event behavior during standby, and PV display settings.
Procedure for setting event types and corresponding alarm values.
Controls the execution and status of the auto-tuning function.
Sets the event type and value for Event 1 alarms.
Sets the event type and value for Event 2 alarms.
Sets the proportional band (P) for Output 1 control.
Selects the alarm type code for Event 1.
Selects the alarm type code for Event 2.
Sets the action for heater break/loop alarm (Lock/Real mode).
Sets the threshold value for heater break alarm.
Sets the threshold value for heater loop alarm.
Selects the type of signal to be output as analog.
Configures the mode for the digital input (DI) terminal.
Sets the communication mode (Local or Communication).
Selects the communication protocol (Shimaden, Modbus ASCII/RTU).
Explanation of Proportional (P), Integral (I), and Derivative (D) control parameters.
Details the soft start function for gradual output control during startup.
Identifies common problems, their causes, and suggested remedies.
Lists specific error codes and their corresponding causes and remedies.
Troubleshooting for issues related to incorrect input measured values.
Troubleshooting for heater break or loop alarm issues.
General| Brand | Shimaden |
|---|---|
| Model | SR92 |
| Category | Controller |
| Language | English |
