Siemens LMV50 series

321/327
Building Technologies Basic DocumentatiohnLMV5... CC1P7550en
23 Index 22.05.2018
Digital inputs 43
X3-02 pin 1 48
X3-04 pin 1 / X3-03 pin 1 42
X4-01 pin 1 / pin 2 44
X4-01 pin 3 44
X4-01 pin 4 43
X4-03 58
X5-01 pin 2 53
X5-02 pin 2 54
X5-03 pin 1 46
X5-03 pin 2 / pin 3 47
X6-01 pin 1 54
X6-01 pin 3 55
X7-03 pin 2 51
X9-03 pin 2 48
X9-03 pin 3 53
X9-03 pin 4 50
digital outputs 56
Digital outputs
X3-01 pin 1 56
X3-01 pin 2 56
X4-02 56
X6-02 58
X8-01 57
X8-02, X8-03, X7-01, X7-02, X6-03 57
X9-01 57
dimensions 234, 302
direct entry of O2 min values 282
direct ignition with heavy oil, modulating28
direct ignition with heavy oil, multistage
28
direct ignition with light oil, modulating
27
direct ignition with light oil, multistage26
direction of rotation 149
display and operating unit AZL5 130
display and settings 139
disposal notes 19
dual-fuel burner gas/heavy oil with gas
pilot ignition 31
dual-fuel burner gas/light oil with gas
pilot ignition 30
duties of the authorized inspector 225
E
eBus PC adapter 224
electrical connection of ionization probe
and flame detector 15
electrical connections and wiring 213
Electronic fuel-air ratio control
Activating / deactivating actuators 85
Actuator addresses 84
Approaching low-fire phase 50/54 89
Direction of rotation of actuator 86
Startpoint operation 88
Electronic ratio control
Traveling times 98
Electronic ratio control
Actuator speed in normal operation
91
Actuator speed outside normal
operation 90
Idle position 87
Ignition positions 87
Limitation of load range 97
Masking out load range 98
Multistage operation 92
Position check, safety time 93
Postpurge positions 90
Prepurge position 87
Program stop 96
Special features 96
Electronic ratio control
Shutdown behavior 98
Electronic ratio control
Overload protection 99
EMC 248
end of operating position 89
entry of password 146
environmental conditions 233
external setpoint changeover 122
external setpoints or predefined load via
digital 122
Extra functions
Extraneous light 69
Extra functions
Continuous fan 69
Forced intermittent operation 65
Gas shortage program 67
Low-fire shutdown 68
Normal / direct start 68
Phase 00 / phase 01 63
Prepurging 66
Program stop function 67
Repetition counter 64
Safety shutdown 65
Start preventions 65
F
first submenu level 147
Flame signal display AZL5
extraneous light 39
flame signal input and flame detector
X10-01 and X10-03 32
fourth submenu level 148
fuel changeover 71
fuel meter 242
fuel meter input X71/X72 242
fuel meter readings 246
fuel train applications 25
fuel-air ratio control system 226
Fuel-air ration control 84
function principle of FGR 289
functioning principle of O2 trim control
252
G
gas direct ignition 25, 73
gas pilot ignition 1 25, 74
gas pilot ignition 2 25, 75
gas valve proving 61
general 20
H
heating up the QGO20 after power-on
257
heavy oil direct ignition 77
heavy oil with gas pilot ignition 79
I
initializing the O2 trim controller 259
input 1, TEMP, Pt100 sensor X60 118