Siemens SINAMICS BOP-2 - Editing Parameters (Scrolling Method)

Siemens SINAMICS BOP-2

54 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Parameters

Basic Operator Panel 2 (BOP-2)

36 Operating Instructions, 02/2016, A5E37143404B AA

Image 9-3 Editing parameters (scrolling method)

Table of Contents

Contents3
Proper Use of Siemens Products4
Warning Notice System4
Qualified Personnel4
Table of Contents5
Changes in this Manual7
Fundamental Safety Instructions9
- General Safety Instructions9
- Industrial Security10
Warnings and Cautions11
Safety Notes11
Introduction13
Overview13
- Layout of the BOP-214
- Description of BOP-2 Physical Characteristics14
- Layout and Functions14
- Function of the BOP-2 Controls15
- Locking and Unlocking the Keypad16
- Screen Icons16
- Screen Icons Description16
- Reaction to Change between HAND and AUTO Mode16
- Menu Structure17
- BOP-2 Basic Menu Structure17
- Menu Structure and Functionality18
- Fitting the BOP-2 to the Control Unit19
Installation19
- Initial Startup20
- Monitoring Screen Information21
Monitoring21
Hand/Auto Mode23
Control23
- Setpoint24
- Torque Setpoint24
- Setpoint Function24
- Jog Function25
- Editing Single Digits25
- Jog25
- Reverse26
- Reverse Function26
- Diagnostic Menu27
- Acknowledge Faults27
- Active Faults and Alarms27
Diagnostics27
- History List Sequence28
- Active Faults and Alarms Sequence28
- History28
- Status29
- Status Word Sequence29
- Control Word 1 (Lower Bits)30
- Control Word 1 (Higher Bits)30
- Control Word 1 (Hexidecimal)30
- Control Word 2 (Lower Bits)30
- Status Word 2 (Lower Bits)31
- Status Word 2 (Hexidecimal)31
- Status Word 2 (Higher Bits)31
- Parameter Menu33
Parameters33
- Editing the Parameters34
- Selecting Standard or Export Parameter Filters34
- Editing Parameters (Single Digit Method)35
- Editing Parameters (Scrolling Method)36
- Editing Parameters37
- Standard Commissioning37
- Setup Menu37
Setup37
- Motor Plate Information, 1.5 Kw38
- Standard Commissioning Example38
- Failure of the Commissioning Process38
- Macro Selection38
- Extras Menu43
- Drive Reset43
Extras43
- Extras - Save Data from RAM to ROM44
- Extras - Saving Data to the BOP44
- Ram - Rom44
- To BOP44
- Extras - Reading Data from the BOP45
- From BOP45
- To Card45
- Extras - Writing Data to the Memory Card46
- Extras - Reading Data from the Memory Card47
- From Card47
- BOP-2 Specifications49
- Index51
Technical Data49

Related product manuals

Preview: Siemens SINAMICS IOP-2

Siemens SINAMICS IOP-2

SINAMICS Intelligent Operator Panel

Sinamics G130 Basic Operator Panel 20

Preview: Siemens Sintony 60

Siemens Sintony 60

Preview: Siemens SINUMERIK ONE MCP 2400

Siemens SINUMERIK ONE MCP 2400

Siemens SINUMERIK MCP-S Series

Preview: Siemens SINUMERIK 840D sl OP 010

Siemens SINUMERIK 840D sl OP 010

Siemens SIMATIC MP 277

Siemens SIMATIC TP 177B

Siemens SIMATIC OP 177B

Siemens SIMATIC OEM PP32

Preview: Siemens SIMATIC HMI series

Siemens SIMATIC HMI series