Connector/Binector (BICO)-Parameters
Parameters
1-487
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
p1009[0...n] CO: Fixed speed setpoint 9 / n_set_fixed 9
p1010[0...n] CO: Fixed speed setpoint 10 / n_set_fixed 10
p1011[0...n] CO: Fixed speed setpoint 11 / n_set_fixed 11
p1012[0...n] CO: Fixed speed setpoint 12 / n_set_fixed 12
p1013[0...n] CO: Fixed speed setpoint 13 / n_set_fixed 13
p1014[0...n] CO: Fixed speed setpoint 14 / n_set_fixed 14
p1015[0...n] CO: Fixed speed setpoint 15 / n_set_fixed 15
r1024 CO: Fixed speed setpoint effective / n_set_fixed eff
r1045 CO: Mot. potentiometer speed setp. in front of ramp-fct. gen. / Mop n_set bef RFG
r1050 CO: Motor. potentiometer setpoint after the ramp-function generator / Mop setp after RFG
r1073 CO: Main setpoint effective / Main setpoint eff
r1077 CO: Supplementary setpoint effective / Suppl setpoint eff
r1078 CO: Total setpoint effective / Total setpoint eff
p1083[0...n] CO: Speed limit in positive direction of rotation / n_limit pos
r1084 CO: Speed limit positive effective / n_limit pos eff
p1086[0...n] CO: Speed limit in negative direction of rotation / n_limit neg
r1087 CO: Speed limit negative effective / n_limit neg eff
r1112 CO: Speed setpoint after minimum limiting / n_set n. min_lim
r1114 CO: Setpoint after the direction limiting / Setp after limit
r1119 CO: Ramp-function generator setpoint at the input / RFG setp at inp
r1149 CO: Ramp-function generator, acceleration / RFG acceleration
r1150 CO: Ramp-function generator speed setpoint at the output / RFG n_set at outp
r1169 CO: Speed controller, speed setpoints 1 and 2 / n_ctrl n_set 1/2
r1170 CO: Speed controller, setpoint sum / n_ctrl setp sum
r1258 CO: Vdc controller output / Vdc_ctrl output
r1298 CO: Vdc controller output (U/f) / Vdc_ctrl output
r1337 CO: Actual slip compensation / Slip comp act val
r1343 CO: I_max controller frequency output / I_max_ctrl f_outp
r1348 CO: U/f control Eco factor actual value / U/f Eco fac act v
r1438 CO: Speed controller, speed setpoint / n_ctrl n_set
r1445 CO: Actual speed smoothed / n_act smooth
r1454 CO: Speed controller system deviation I component / n_ctrl sys dev Tn
r1468 CO: Speed controller P-gain effective / n_ctr Kp eff
r1482 CO: Speed controller I torque output / n_ctrl I-M_output
r1490 CO: Droop feedback speed reduction / Droop n_reduction
r1493 CO: Moment of inertia, total / M_inertia total
r1508 CO: Torque setpoint before supplementary torque / M_set bef. M_suppl
r1516 CO: Supplementary torque and acceleration torque / M_suppl + M_accel
r1518[0...1] CO: Accelerating torque / M_accel
p1520[0...n] CO: Torque limit upper / M_max upper
p1521[0...n] CO: Torque limit lower / M_max lower
p1524[0...n] CO: Torque limit upper/motoring scaling / M_max up/mot scal
p1525[0...n] CO: Torque limit lower scaling / M_max lower scal
r1526 CO: Torque limit upper without offset / M_max up w/o offs
r1527 CO: Torque limit lower without offset / M_max low w/o offs
r1538 CO: Upper effective torque limit / M_max upper eff
r1539 CO: Lower effective torque limit / M_max lower eff
r1547[0...1] CO: Torque limit for speed controller output / M_max outp n_ctrl
r1548[0...1] CO: Stall current limit torque-generating maximum / Isq_max stall
p1570[0...n] CO: Flux setpoint / Flux setpoint
r1593[0...1] CO: Field weakening controller / flux controller output / Field/Fl_ctrl outp
r1597 CO: Field weakening controller output / Field_ctrl outp
r1598 CO: Total flux setpoint / Flux setp total
To Next Page
Loading...
