Siemens SINAMICS G120 - Page 488

Parameters
Connector/Binector (BICO)-Parameters
1-488
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
r1718 CO: Isq controller output / Isq_ctrl outp
r1723 CO: Isd controller output / Isd_ctrl outp
r1732[0...1] CO: Direct-axis voltage setpoint / Direct U set
r1733[0...1] CO: Quadrature-axis voltage setpoint / Quad U set
r1770 CO: Motor model speed adaptation proportional component / MotMod n_adapt Kp
r1771 CO: Motor model speed adaptation I comp. / MotMod n_adapt Tn
r1801[0...1] CO: Pulse frequency / Pulse frequency
r1809 CO: Modulator mode actual / Modulator mode act
r2050[0...7] CO: PROFIBUS PZD receive word / PZD recv word
r2089[0...4] CO: Send binector-connector converter status word / Bin/con ZSW send
r2120 CO: Sum of fault and alarm buffer changes / Sum buffer changed
r2121 CO: Counter, alarm buffer changes / Alrm buff changed
r2131 CO: Actual fault code / Actual fault code
r2132 CO: Actual alarm code / Actual alarm code
r2169 CO: Actual speed smoothed signals / n_act smth message
p2201[0...n] CO: Technology controller, fixed value 1 / Tec_ctr fix val 1
p2202[0...n] CO: Technology controller, fixed value 2 / Tec_ctr fix val 2
p2203[0...n] CO: Technology controller, fixed value 3 / Tec_ctr fix val 3
p2204[0...n] CO: Technology controller, fixed value 4 / Tec_ctr fix val 4
p2205[0...n] CO: Technology controller, fixed value 5 / Tec_ctr fix val 5
p2206[0...n] CO: Technology controller, fixed value 6 / Tec_ctr fix val 6
p2207[0...n] CO: Technology controller, fixed value 7 / Tec_ctr fix val 7
p2208[0...n] CO: Technology controller, fixed value 8 / Tec_ctr fix val 8
p2209[0...n] CO: Technology controller, fixed value 9 / Tec_ctr fix val 9
p2210[0...n] CO: Technology controller, fixed value 10 / Tec_ctr fix val 10
p2211[0...n] CO: Technology controller, fixed value 11 / Tec_ctr fix val 11
p2212[0...n] CO: Technology controller, fixed value 12 / Tec_ctr fix val 12
p2213[0...n] CO: Technology controller, fixed value 13 / Tec_ctr fix val 13
p2214[0...n] CO: Technology controller, fixed value 14 / Tec_ctr fix val 14
p2215[0...n] CO: Technology controller, fixed value 15 / Tec_ctr fix val 15
r2224 CO: Technology controller, fixed value effective / Tec_ctr FixVal eff
r2245 CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
r2250 CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
r2260 CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
r2262 CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
r2266 CO: Technology controller actual value after filter / Tec_ctr act aftFlt
r2272 CO: Technology controller actual value scaled / Tech_ctrl act scal
r2273 CO: Technology controller error / Tec_ctrl error
p2291 CO: Technology controller maximum limiting / Tec_ctrl max_limit
p2292 CO: Technology controller minimum limiting / Tec_ctrl min_lim
r2294 CO: Technology controller output signal / Tec_ctrl outp_sig
p2295 CO: Technology controller output scaling / Tec_ctrl outp scal
r2344 CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
r2397[0...1] CO: Hibernation output speed actual / Hib n_outp act
p2900[0...n] CO: Fixed value 1 [%] / Fixed value 1 [%]
p2901[0...n] CO: Fixed value 2 [%] / Fixed value 2 [%]
r2902[0...14] CO: Fixed values [%] / Fixed values [%]
p2930[0...n] CO: Fixed value M [Nm] / Fixed value M [Nm]
r3131 CO: Current flt value / Current flt value
r3132 CO: Actual component number / Act comp_no.
r8784 CO: CAN status word / Status word
r11060 CO: Free tec_ctrl 0 setpoint after ramp-function generator / Ftec0 setp aft RFG
r11072 CO: Free tec_ctrl 0 actual value after limiter / Ftec0 act v af lim