Siemens SINAMICS G120C - Page 68

Commissioning
4.2 Commissioning with BOP-2 operator panel
SINAMICS G120C, FSD ... FSF inverters
68 Compact Operating Instructions, 11/2016, FW V4.7 SP6, A5E39339884B AA
No.
Description
p2037
PROFIdrive STW1.10 = 0 mode
0 Freeze setpoints and further process sign-
of-life
1
Freeze setpoints and sign-of-life
2 Setpoints are not frozen
p2038
PROFIdrive STW/ZSW interface mode
0
SINAMICS
2
VIK-NAMUR
r2043
BO: PROFIdrive PZD state
.00 1 = setpoint failure .02 1 = fieldbus run-
ning
p2044
PROFIdrive fault delay [s]
r2050
CO: PROFIdrive PZD receive word
[0]
PZD 1 …
[7]
PZD 8
p2051
CI: PROFIdrive PZD send word
[0]
PZD 1 …
[7]
PZD 8
r2053
PROFIdrive diagnostics send PZD word
[0]
PZD 1 …
[7]
PZD 8
r2060
CO: IF1 PROFIdrive PZD receive double word
[0]
PZD 1 + 2 …
[10]
PZD 11 + 12
r2061
CI: IF1 PROFIdrive PZD send double word
[0]
PZD 1 + 2 …
[10]
PZD 11 + 12
r2063 IF1 PROFIdrive diagnostics PZD send double
word
[0]
PZD 1 + 2 …
[10]
PZD 11 + 12
r2067 IF1 PZD maximum interconnected
[0]
Receiving
[1]
Sending
p2072
Response, receive value after PZD failure
.00 Unconditionally
open holding
brake (p0855)
1 = freeze value
0 = zero value
r2074
PROFIdrive diagnostics bus address PZD receive
[0]
PZD 1 …
[7]
PZD 8
r2077 PROFIBUS diagnostics peer-to-peer data transfer
addresses
p2079
PROFIdrive PZD telegram selection extended
See p0922
p2080
BI: Binector-connector converter, status word 1
The individual bits are combined to form status
word 1.
p2088
Binector-connector converter, invert status word
No.
Description
r2089 CO: Send binector-connector converter status
word
[0] Status word 1
[1]
Status word 2
[2] Free status word 3
[3]
Free status word 4
[4]
Free status word 5
r2090
BO: PROFIdrive PZD1 receive bit-serial
r2091
BO: PROFIdrive PZD2 receive bit-serial
r2092
BO: PROFIdrive PZD3 receive bit-serial
r2093
BO: PROFIdrive PZD4 receive bit-serial
r2094
BO: Connector-binector converter binector output
r2095
BO: Connector-binector converter binector output
p2098 Invert connector-binector converter binector out-
put
p2099
CI: Connector-binector converter signal source
p2100
Setting the fault number for fault response
p2101
Setting the fault response
0
None
1
OFF1
2
OFF2
3
OFF3
5
STOP2
6
DC braking
p2103
BI: 1. Acknowledge faults
p2104
BI: 2. Acknowledge faults
p2106
BI: External fault 1
r2110
Alarm number
p2111
Alarm counter
p2112
BI: External alarm 1
p2118
Change message type, message number
p2119
Change message type, type
1
Fault
2
Alarm
3
No message
r2122
Alarm code
r2123 Alarm time received [ms]
r2124
Alarm value
r2125 Alarm time removed [ms]
p2126
Setting fault number for acknowledge mode
p2127
Sets acknowledgement mode
p2128
Selecting fault/alarm code for trigger
r2129
CO/BO: Trigger word for faults and alarms
r2130
Fault time received in days
r2131
CO: Actual fault code