Siemens SINUMERIK 808D ADVANCED T User Manual

© Siemens AG 2012 - 2013. All rights reserved
6FC5397-0FP40-0BA0, 08/2013
1
SINUMERIK
SINUMERIK 808D ADVANCED
PLC Subroutines Manual
User Manual
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The
notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage
have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury
will
result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury
may
result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of
injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific task in accordance with
the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their
training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products
and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,
installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Siemens SINUMERIK 808D ADVANCED T Specifications

General

Control Type	CNC
Input Voltage	24 V DC
Communication Interfaces	USB, Ethernet
Protection Class	IP54
PLC	Integrated
Interpolation	Linear, Circular
Number of Spindles	1 spindle

Summary

Siemens PLC Programming Legal Information

Warning Notice System

Explains the grading and use of danger notices in the manual.

Proper Use of Siemens Products

Provides essential notes on the correct usage of Siemens products.

Preface to SINUMERIK PLC Manual

Applicable Products

Lists the control systems to which this manual applies.

Technical Support Information

Offers hotline and web support details for technical assistance.

Overview of SINUMERIK 808D

System Resource Distribution

Details the distribution of system resources into PLC system, memory, and timers.

SINUMERIK PLC Programming Tool

Installing the 808D Toolbox

Guides users on installing the 808D Toolbox software on their PC.

Establishing Communication

Guides on setting up communication via RS232 and Ethernet interfaces.

PLC Application Management

Describes saving, copying, and transferring PLC projects using software or USB.

SINUMERIK PLC Subroutines

PLC Machine Data

Presents tables detailing PLC machine data for various functions.

Subroutine 20 - AUX_MCP (Auxiliary Functions)

Controls machine auxiliary functions like lamps, safe door, and chip remover.

Subroutine 33 - EMG_STOP (Emergency Stop)

Handles the Emergency Stop function, generating alarms and disabling control signals.

Subroutine 40 - AXIS_CTL (Axis Control)

Controls drive pulse enable, controller enable, hardware limits, and spindle enable signals.

Use of User Alarms

Alarm Reference List

Lists user alarms, their interface addresses, descriptions, and originating subroutines.

PLC Sample Applications

PLC Sample Application (Turning)

Details a sample application for turning machines with specific configurations.

PLC Sample Application (Milling)

Details a sample application for milling machines with specific configurations.