EasyManua.ls Logo

Siemens Sitrans LR200 - User Manual

Siemens Sitrans LR200
185 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instruction Manual February 2008
LR200 (PROFIBUS PA)
sitrans
Siemens Industrial

Table of Contents

Other manuals for Siemens Sitrans LR200

Preview: Quick Start Manual
Quick Start Manual268 pages
Preview: Compact Operating Instructions
Compact Operating Instructions45 pages

Questions and Answers

  • J
    Jason PonceAug 12, 2025
    Why is my Siemens Measuring Instruments overheating?
    • K
      Katherine WarrenAug 12, 2025
      If the internal temperature of the Siemens Measuring Instruments device has exceeded specifications, it is operating outside its temperature range. You should relocate the device and/or lower the process temperature to cool the device. Inspect for heat-related damage and contact your local Siemens representative if repair is required. Note that the fault code will persist until a manual reset is performed using SIMATIC PEM or the LCD interface.
  • K
    Kimberly BrownAug 16, 2025
    What to do if Siemens Measuring Instruments user configuration is invalid?
    • H
      harrisbrianAug 16, 2025
      If the user configuration for Siemens Measuring Instruments is invalid, reconfigure the unit. Make sure that the difference between the High Calibration Point and Low Calibration Point is not less than or equal to zero; if needed, perform a Master Reset.
  • J
    Joel SmithAug 19, 2025
    What to do if Siemens Measuring Instruments are nearing lifetime limit?
    • B
      Brittany SmithAug 19, 2025
      If the Siemens Measuring Instruments device is nearing its lifetime limit according to the value set in Maintenance Required Limit, replacement is recommended.
  • K
    Kimberly BarnesAug 25, 2025
    What to do if Siemens Measuring Instruments device is nearing its Maintenance Demanded Limit?
    • G
      garrettjimmyAug 25, 2025
      If the Siemens Measuring Instruments device is nearing its lifetime limit according to the value set in Maintenance Demanded Limit, replacement is recommended.
  • J
    Janet ChandlerAug 27, 2025
    What to do if Siemens Measuring Instruments sensor is nearing its Maintenance Required Limit?
    • S
      seth64Aug 27, 2025
      If the Siemens Measuring Instruments sensor is nearing its lifetime limit according to the value set in Maintenance Required Limit, replacement is recommended.
  • S
    Stephanie JenkinsAug 31, 2025
    What to do if Siemens Measuring Instruments sensor is nearing its Maintenance Demanded Limit?
    • B
      Brian AlexanderAug 31, 2025
      If the Siemens Measuring Instruments sensor is nearing its lifetime limit according to the value set in Maintenance Demanded Limit, replacement is recommended.
  • C
    Cesar VelazquezSep 3, 2025
    What to do if Siemens Measuring Instruments service interval has expired?
    • W
      William WebbSep 3, 2025
      If the service interval as defined in Maintenance Required Limit has expired for Siemens Measuring Instruments, perform service.
  • J
    Jack LopezSep 7, 2025
    What to do if Siemens Measuring Instruments Maintenance Demanded Limit has expired?
    • C
      Carlos BoydSep 8, 2025
      If the service interval as defined in Maintenance Demanded Limit has expired for Siemens Measuring Instruments, perform service.

Summary

Safety Notes

SITRANS LR200: Overview

Programming

Specifications

Installation

Wiring

Connecting SITRANS LR200 (PROFIBUS PA)

Steps for wiring the PROFIBUS PA connection.

Basic PLC configuration with PROFIBUS PA

Setting up a PLC for PROFIBUS PA communication.

Operating via the handheld programmer

Programming SITRANS LR200

How to change parameter settings for specific applications.

Quick Start Wizard via the handheld programmer

Step-by-step guide for initial device configuration.

Operating via SIMATIC PDM

Quick Start Wizard via SIMATIC PDM

Guide for configuring the device using SIMATIC PDM software.

Changing parameter settings using SIMATIC PDM

How to adjust parameters remotely via SIMATIC PDM.

Device Description (DD)

Configuring a new device

Steps for installing and configuring a new device description.

Sensor calibration

Procedure for calibrating the device's sensor.

Parameter Reference

Quick Start Wizard

Groups settings for simple application configuration.

Maintenance

Appendix B: Troubleshooting

Communication Troubleshooting

Steps to resolve communication issues with the device.

General Fault Codes

List of fault codes and their corrective actions.

Operation Troubleshooting

Common operating symptoms and their solutions.

Appendix D: Technical Reference

Principles of Operation

Auto False Echo Suppression

Method to improve accuracy by filtering false echoes.

Appendix G: Communications via PROFIBUS PA

Network Configuration

PROFIBUS address

Diagnostics

Fault Reset

Procedures to acknowledge and clear detected faults.

Acyclic Extended Diagnostics (General Fault Codes)

Mounting Guidelines

2.4 FAIL-SAFE

3. DIAGNOSTICS

Overview of diagnostic functions and parameters.

4. SERVICE (cont’d)

Maintenance and service-related functions.

Siemens Sitrans LR200 Specifications

General IconGeneral
BrandSiemens
ModelSitrans LR200
CategoryTransmitter
LanguageEnglish

Related product manuals