Silverline 580430 - Operation; Setting tool power; Changing orbital mode; Maintenance

Air Sander & Polisher 150mm 580430
7
silverlinetools.com
Operation
Note: Itisadvisedthatyoupracticeusingthistoolonapieceofscrapwood.Tryitinbothorbitalmodes
(see'Changingorbitalmode')tofamiliariseyourselfwitheach.
1. GriptheHandle(4)rmlywithonehand,soyourthumbcanoperatetheSpeedControl(3)
2. HoldtheBodyCover(1)withyourotherhand,tocontrolthetoolandapplypressuretothe
workpiece
3. FirstlysqueezetheSpeedControlgentlytofamiliariseyourselftothewaythetooloperates
Note:YoucanadjustthespeedofthetoolbyadjustingthepressureyouapplytotheSpeedControl.
4. Beginbyholdingthetoolgentlyagainsttheworkpiece,andslowlybuildingupspeedandpressure
WARNING:Thefrictionbetweenabrasiveandmaterialwillcauseheat.Checktheworkpiece
frequentlytoensureitdoesnotburn.
WARNING:Beawarethatairtoolsmayholdresidualpressureafteruse.Alwaysbleedairpressure
fromthetoolaftershuttingoffairsupply.
Accessories
AccessoriesforthistoolincludingadhesivesandingdiscsareavailablefromyourSilverlinestockist.
SparepartscanbeobtainedfromyourSilverlinedealerorwww.toolsparesonline.com
Maintenance
WARNING:Alwaysdisconnectfromtheairsupplyanddepressurisebeforecleaningorcarrying
outanymaintenance.
Cleaning
• Keepyourtoolcleanatalltimes.Dirtanddustwillcauseinternalpartstowearquickly,andshorten
themachine’sservicelife.Cleanthebodyofyourmachinewithasoftbrush,ordrycloth
IMPORTANT: Thereisverylittlethatcangowrongwithyourairtoolanditshouldbenotedthatwhen
anairtoolfailstoworkitisgenerallybecausetheinternalworkingshavecorrodedduetodirty,wetair
andfailuretofollowtheinstructionsgivenbelow.
Daily maintenance procedure
Ifaninlinelubricatorisnotttedtotheairsupply,thetoolmustbemanuallylubricated:
1. Disconnectfromtheairsupply
2. Pour3-4dropsofoilintotheairintake
3. Operatethemachineatlowspeedtothoroughlylubricateallinternalworkings
• Ifthemachineisinconstantuseorusedforlongperiodsatatime,repeattheaboveprocedureup
to3timesperday
• Useairtooloil.DONOTUNDERANYCIRCUMSTANCESUSENORMALENGINEOIL
• Failuretocomplywiththeoperatingandmaintenanceinstructionsmayinvalidatetheguarantee
Storage
• Storethistoolcarefullyinasecure,dryplaceoutofthereachofchildren
Contact
Fortechnicalorrepairserviceadvice,pleasecontactthehelplineon(+44)1935382222
Web: www.silverlinetools.com
UK Address:
ToolstreamLtd.
BoundaryWay
LuftonTradingEstate
Yeovil,Somerset
BA228HZ,UnitedKingdom
EU Address:
ToolstreamB.V.
Holtum-Noordweg11
Unit4
6121REBorn
The Netherlands
Disposal
• Aswithotherpowertools,airtoolsshouldnotbedisposedofwithhouseholdwaste
• Airtoolsmaycontaintracesoftooloilandotherlubricantsandsomustberecycledaccordingly
• Contactyourlocalwastedisposalauthorityforinformationonthecorrectwaytodisposeof
powertools
580430_OwnerManual.indd 7580430_OwnerManual.indd 7 12/04/2023 11:0312/04/2023 11:03