Sinoboom GTTZ10EJ - Default Chapter; Table of Contents

GTTZ10EJ Operation Manual i © Nov. 2020
TABLE OF CONTENTS
Introduction ............................. iii
1 Machine Specifications ........ 1-1
2 Machine Components .......... 2-1
3 Safety ............................... 3-1
Safety Definitions . . . . . . . . . . . . . . . . . . . . . 3-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 3-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 3-1
Tipping Hazards and Rated Load . . . . . 3-2
Work Environment Hazards . . . . . . . . . . . 3-4
Unsafe Operation Hazards. . . . . . . . . . . . 3-5
Fall Hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 3-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Explosion and Fire Hazards. . . . . . . . . . . 3-8
Damaged Machine Hazards . . . . . . . . . . 3-8
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-9
Battery Hazards . . . . . . . . . . . . . . . . . . . . . . . 3-9
Welding and Polishing Requirements3-10
Lockout after Each Use . . . . . . . . . . . . . .3-10
4 Jobsite Inspection............... 4-1
5 Pre-operation Inspection ...... 5-1
Tips for Conducting a Pre-operation
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Conducting a Pre-operation
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Inspecting Parts . . . . . . . . . . . . . . . . . . . . . . . 5-2
Inspecting Entire Machine . . . . . . . . . . . . 5-2
Inspecting Hydraulic Oil Level. . . . . . . . . 5-2
Inspecting the Battery level . . . . . . . . . . . 5-3
6 Pre-operation Function Test .. 6-1
Preparing for a Pre-operation Func-
tion Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Ground Controls . . . . . . . . . . . . . . . . . . . . . . 6-1
Platform Controls . . . . . . . . . . . . . . . . . . . . . 6-4
Testing the Drive Speed. . . . . . . . . . . . . . . 6-8
Testing the Emergency Lowering . . . . . 6-8
Mast emergency lowering . . . . . . . . . . 6-8
Jib boom emergency lowering . . . . . . 6-8
Testing the Pothole Protection . . . . . . . . 6-9
Testing the Tilt Protection . . . . . . . . . . . . . 6-9
Testing the Weighing System . . . . . . . .6-10
7 Operating the machine ......... 7-1
Stability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Emergency Stop . . . . . . . . . . . . . . . . . . . . . . 7-3
Emergency Operating. . . . . . . . . . . . . . . . . 7-4
Emergency Control . . . . . . . . . . . . . . . . . . . 7-4
Emergency Towing/Dragging . . . . . . . . . 7-5
Charging the Battery . . . . . . . . . . . . . . . . . . 7-6
Driving on a Slope. . . . . . . . . . . . . . . . . . . . . 7-7
8 Transporting and Lifting the
Machine ........................... 8-1
Lifting the Machine with a Crane . . . . . . 8-2
Transporting the Machine . . . . . . . . . . . . . 8-3
9 Maintenance ...................... 9-1
Maintenance Schedule. . . . . . . . . . . . . . . . 9-1
Conducting a Pre-delivery Inspection . 9-4
Maintenance Inspection Report . . . . . . . 9-5
10 Decals/Nameplates
Inspection ....................... 10-1
Decals/Nameplates(GB). . . . . . . . . . .10-2
Decals/Nameplates(CE-Metric) . . .10-5
Decals/Nameplates(CE-Imperial) .10-8
Decals/Nameplates(ANSI). . . . . . . .10-11
Appendix 1: Symbols and
Description....................... A-1