SolarEdge L30US-IB80 - 4.3.7.5. Dry Contact Setup

To Next Page

To Previous Page

L30US-IB80, L30US-IB00, L40US UPS

4.3.7.5.

Dry contact setup

Battery Abnormal BCB trip (DRV): Enable or disable BCB trip single output. The default

value is Disable.

Bypass Feedback Trip: Enable or disable bypass feedback output. The default value is

Disable.

External Maint. Breaker (MT): Enable or disable external maintenance breaker connection

detection. The default value is Disable.

Battery breaker (BAT): Enable or disable battery breaker connection detection. The default

value is Disable.

NOTE!

Each dry contact can be N.O or N.C.

Main Page

Table of Contents5
Preface9
Standards and Conventions9
Safety Symbols Information9
Technical Support10
Important Safety Instructions (Save These Instructions)11
Table 1 Batteries Quantity13
Main Features14
Summary14
Functions and Features14
System Configuration15
Cabinet View16
Figure 1 Front View/Side View of L30US-IB80, L30US-IB00 and L40US16
Figure 2 Front View (Without Door) and Rear View of L30US-IB80 and L30US-IB0016
Figure 3 Front View (Without Door) and Rear View of L40US17
Table 2 Cabinet Overview17
Dimensions and Weight18
Figure 4 Dimensions18
Table 3: Dimensions and Weights19
Communication Panel20
Computer Access20
Figure 5 Communication Panel20
Table 4 Communication Panel20
Figure 6 Muser5000 Homepage21
Figure 7 Muser5000 Communication Setting Page21
Figure 8 Muser5000 Append Equipment Page22
Figure 9 Muser5000 Append Equipment Manual Setting Page22
Operation23
Operation Modes23
Normal Mode23
Battery Mode (Stored Energy Mode)23
Figure 10 Normal Mode23
Maintenance Mode (Manual Bypass)24
Bypass Mode24
Figure 11 Battery Mode24
Figure 12 Maintenance Mode (Manual Bypass)24
ECO Mode25
Figure 13 Bypass Mode25
Figure 14 Eco Mode25
Ups Operation26
Start Procedure26
Test Procedure26
Maintenance Bypass27
Switch to Mechanical Bypass27
Switch to Normal Operation (from Mechanical Bypass)27
Cold Start Procedure28
Shutdown Procedure29
Figure 15 Cold Start Button29
Parallel Setting30
Figure 16 Muser5000 Homepage30
Figure 17 Muser5000 User Setting Page31
Figure 18 Muser5000 Work Mode Setting Page31
Figure 19 Muser5000 UPS ID Setting Page32
Lcd Control Panel33
Overview33
Introduction34
Data35
Status35
Main36
Bypass37
Output37
Battery38
Status Info39
Alarm41
Current Alarm41
History42
Buzzer42
Setting43
Basic Setting44
Language45
Password45
Brightness and Backlight Time46
Date and Time Setting47
Communication Setting47
Bypass Settings48
Advanced Settings50
System Setting51
Parallel Setting53
Output Setting54
Battery Setting55
Dry Contact Setup57
Maintenance: Touch Correction and Battery Self-Test58
Battery Self-Check58
Timing Daily59
Timing Weekly59
Common60
Inv On/Off60
Battery Test61
Fault Clear62
Monitor and LCD Software Version62
Display Messages and Troubleshooting63
Operational Status and Mode(S)63
Table 6 Operational Status and Mode63
Faults and Alarms Reports64
Table 7 Fault Information64
Table 8 Alarm Information66
Optional Features68
SNMP Card68
Functions68
Relay Card69
Figure 22 Relay Contacts (Dry Contact Card)69
Table 9 Relay Contacts (Communication Card)69
Figure 23 Relay Overview70
Appendix 1: Specifications71
Table 10 Specifications71
Appendix 2: Troubleshooting76
Table 11 Problems and Solutions76

SolarEdge L30US-IB80 - 4.3.7.5. Dry Contact Setup

Table of Contents

Other manuals for SolarEdge L30US-IB80