To Next Page
D
Dr. Melissa LeSep 18, 2025
What to do if devices on the home network cannot connect to Sony STR-DN1030?
- SStacey BradleySep 18, 2025
If devices on the home network cannot connect to the receiver, enable 'Network Standby'. Check network setup.
What to do if devices on the home network cannot connect to Sony STR-DN1030?
If devices on the home network cannot connect to the receiver, enable 'Network Standby'. Check network setup.
Why Sony STR-DN1030 cannot be turned on automatically when accessed by devices on the network?
If the receiver cannot be turned on automatically when accessed by devices on the network, set 'Network Standby' to 'On'.
Why is a test tone not output from the speakers of my Sony Receiver?
If a test tone is not output from the speakers, inspect speaker cord connections. Check for short-circuits in speaker cords. Disable PARTY STREAMING.
What to do if a test tone is output from a different speaker than the speaker displayed on the TV screen of Sony Receiver?
If a test tone is output from a different speaker than the speaker displayed on the TV screen, ensure that the speaker connections and the speaker pattern match correctly.
Why is there a time gap between the audio output and visual display on my Sony Receiver?
If there is a time gap between the audio output and visual display, verify that PARTY STREAMING is disabled.
How to fix no sound or low sound from specific speakers on Sony Receiver?
If there is no sound or only a very low-level sound from specific speakers, connect a pair of headphones to the PHONES jack to verify that sound is output from the headphones. If only one channel is output from the headphones, the equipment may not be connected to the receiver correctly. Check that all the cords are fully inserted into the jacks on both the receiver and the equipment. If both channels are output from the headphones, the front speaker may not be connected to the receiver correctly. Check the connection of the front speaker which is not outputting any sound. Make sure you have connected to both the L and R jacks of an analog equipment, analog equipment requires both L and R jack connections. Use an audio cord (not supplied). Adjust the speaker level as necessary. Use Auto Ca...
What to do if there is no sound from a specific equipment connected to Sony STR-DN1030?
If there is no sound from a specific equipment, first check that the equipment is correctly connected to the audio input jacks for that equipment and that the cords are fully inserted into the jacks on both the receiver and the equipment. Check the INPUT MODE and adjust it as needed. Also, ensure the equipment is correctly connected to the HDMI jack. Note that you cannot listen to Super Audio CD by connecting HDMI; use an alternative connection. Depending on the playback equipment, you may need to set up the HDMI setting of the equipment. Be sure to use a High Speed HDMI cable when you view images or listen to sound, especially for the 1080p, Deep Color (Deep Colour) or 3D transmission. Sound may not be output from the receiver while the GUI appears on the TV screen, so deactivate the GUI ...
Why does my Sony STR-DN1030 have no image output in standby mode?
When the receiver enters into standby mode, image is from the last HDMI equipment selection before you turned off the receiver. If you are enjoying other equipment, play the equipment and perform the One-Touch Play operation, or turn on the receiver to select the HDMI equipment you want to enjoy. If you connect equipment not compatible with the “BRAVIA” Sync to the receiver, set “Pass Through” to “ON” in the HDMI Settings menu.
What to do if there is no sound from my Sony Receiver?
If you are experiencing no sound from your Sony Receiver, ensure all connecting cords are securely inserted into the input/output jacks of the receiver, speakers, and equipment. Also, verify that both the receiver and all connected equipment are turned on. Check that the MASTER VOLUME control is not set to 'VOL MIN' and that the SPEAKERS are set to 'ON'. Ensure headphones are not connected, and the muting function is off. Try selecting the desired input equipment. If you want to listen to the sound from the TV speaker, set the 'Audio Out' to 'TV+AMP' in the HDMI Settings menu. Sound may be interrupted when the sampling frequency, the number of channels or audio format of audio output signals from the playback equipment is switched, so adjust the audio settings to stabilize the output.
How to fix unbalanced or reversed left and right sounds on Sony STR-DN1030 Receiver?
To correct unbalanced or reversed left and right sounds, ensure correct and secure connections of the speakers and equipment. Additionally, adjust the sound level parameters using the Speaker Settings menu.
Overview of the front panel controls and indicators.
Steps for installing and connecting speakers.
Instructions for connecting TV and video devices.
Steps for connecting audio devices.
Initial setup procedures for the receiver.
How to select speaker patterns and perform auto calibration.
Guide to connecting devices via HDMI.
Steps for connecting SACD or CD players.
How to set the voltage selector for local power.
Instructions for connecting the AC power cord.
Procedure for initial receiver setup and factory reset.
How to select the appropriate speaker pattern.
How to configure surround back speaker usage.
Guide to setting up a wireless network connection.
How to navigate and use the receiver's on-screen menu.
How to select and play content from connected equipment.
How to listen to FM and AM radio broadcasts.
How to select and adjust sound fields.
Overview of network features like DLNA, SEN, AirPlay.
Steps to set up Windows Media Player 12 as a server.
How to refresh the server list to find new servers.
How to remove a server from the list.
How to find the receiver's registration code for music services.
Details on the receiver's Bluetooth capabilities and profiles.
Explanation of the BRAVIA Sync function.
Setup for BRAVIA Sync when TV supports Easy Setting.
How to select audio input mode.
How to reassign video and audio input jacks.
How to operate the receiver in zone 2.
How to navigate and use the Settings menu.
How to program the remote for other equipment.
General| Display | - |
|---|---|
| Product color | Black |
| Audio decoders | Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS-ES, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1) |
| x.v.Color support | Yes |
| Apple docking compatibility | Not supported |
| HDMI in | 5 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 2 |
| RMS rated power | 1015 W |
| Audio output channels | 7.2 channels |
| Total Harmonic Distortion (THD) | 0.01 % |
| Power output per channel (1KHz@8 Ohm) | 120 W |
| Power output per channel (20-20KHz@8 Ohm) | 145 W |
| Connectivity technology | Wired & Wireless |
| Supported radio bands | AM, FM |
| Preset stations quantity | 60 |
| Optical drive included | No |
| Power consumption (standby) | 0.3 W |
| Package weight | 11000 g |
Weight and Dimensions| Depth | 322.6 mm |
|---|---|
| Width | 430 mm |
| Height | 158 mm |
