ST FP-SNS-DATALOG2 - Slide 2: Agenda

62 pages

To Next Page

To Previous Page

Agenda

Hardware and Software overview

Documents & Related Resources

Setup & Demo Examples

Main Page

Slide 1: Quick Start Guide STM32Cube function pack for high speed datalogging and ultrasound processing (FP-SNS-DATALOG2)1
Slide 2: Agenda2
Slide 3: 1 - Hardware and Software overview3
Slide 4: STWIN.box development kit - STEVAL-STWINBX1 Hardware Overview4
Slide 5: STWIN.box development kit - STEVAL-STWINBX1 Hardware Overview5
Slide 6: STWIN.box Modular platform expansion - STEVAL-C34KAT1 Hardware Overview6
Slide 7: STWIN.box Modular platform expansion - STEVAL-C34KAT2 Hardware Overview7
Slide 8: STWIN development kit - STEVAL-STWINKT1B Hardware Overview8
Slide 9: Sensortile.box PRO development kit - STEVAL-MKBOXPRO Hardware Overview9
Slide 10: Discovery kit for IoT node - B-U585I-IOT02A Hardware Overview10
Slide 11: Motion and microphone expansion board - X-NUCLEO-IKS02A1 Hardware Overview11
Slide 12: FP-SNS-DATALOG2 Software Overview12
Slide 13: DATALOG2 demonstration13
Slide 14: DATALOG2 vs DATALOG114
Slide 15: 2 - Setup & Demo Examples15
Slide 16: HW prerequisites16
Slide 17: HW prerequisites17
Slide 18: HW prerequisites18
Slide 19: Software and other prerequisites19
Slide 20: Samples demonstrations20
Slide 21: Firmware Update – FFOTA for STWIN.box21
Slide 22: Firmware Update – FFOTA for STWIN.box and Sensortile.box PRO22
Slide 23: Firmware Update – FFOTA for STWIN.box and Sensortile.box PRO23
Slide 24: Firmware Update – FFOTA for STWIN.box and Sensortile.box PRO24
Slide 25: Firmware Update – ST-LINK25
Slide 26: Firmware Update – USB26
Slide 27: 2.1 – DATALOG2 Demonstration27
Slide 28: 2.1.1 - USB sensor data streaming Command Line Interface28
Slide 29: cli_example overview29
Slide 30: Modify device and sensors configuration30
Slide 31: Run the application31
Slide 32: 2.1.2 - USB sensor data streaming Real Time Plot32
Slide 33: Execute hsdatalog_GUI.py33
Slide 34: hsdatalog_GUI.py34
Slide 35: hsdatalog_GUI.py35
Slide 36: hsdatalog_GUI.py36
Slide 37: 2.1.3 – Data logging on SD card, configuration with BLESensor App *37
Slide 38: ST BLESensor App: DATALOG2 tab38
Slide 39: Configure MLC39
Slide 40: Acquisition settings and control40
Slide 41: ST BLESensClassic App: DATALOG2 tab41
Slide 42: 2.1.4 – Data logging on SD card, standalone mode42
Slide 43: Start an acquisition in standalone mode43
Slide 44: Automode44
Slide 45: Automode45
Slide 46: 2.2 – HSDPython_SDK46
Slide 47: HSDPython_SDK47
Slide 48: HSDPython_SDK48
Slide 49: HSDPython_SDK installation49
Slide 50: HSDPython_SDK scripts50
Slide 51: HSDPython_SDK scripts51
Slide 52: 2.3 – UltrasoundFFT for STWIN.box52
Slide 53: UltrasoundFFT on STWINKT1B53
Slide 54: FP-SNS-DATALOG2 - UltrasoundFFT54
Slide 55: FP-SNS-DATALOG2 - UltrasoundFFT55
Slide 56: 3 - Documents & Related Resources56
Slide 57: Documents & Related Resources57
Slide 58: Documents & Related Resources58
Slide 59: 4 - STM32 Open Development Environment: Overview59
Slide 60: STM32 ODE Ecosystem60
Slide 61: STM32 Open Development Environment: all that you need61
Slide 6262

ST FP-SNS-DATALOG2 - Slide 2: Agenda

Table of Contents