Stanley FATMAX D251/10/50S - Safety Precautions; Before Use Environmental Guidelines; General Safety Instructions; Assembly

G
B
17
Before using the compressor, read the instructions for use carefully
and comply with the following safety precautions. Consult this
handbook if you have any doubts regarding functioning.
Preserve all the documentation so that anyone who uses the
compressor can consult this beforehand.
SAFETY PRECAUTIONS
1
An ACOUSTIC PRESSURE value of 4 m. corresponds to the ACOUSTIC
POWER value stated on the label located on the compressor, minus 20 dB.
BEFORE USE
• The compressor must be used in a suitable environment (well
ventilated with an ambient temperature of between +5°C and +40°C)
and never in places affected by dust, acids, vapors, explosive or
flammable gases.
•Always maintain a safety distance of at least 4 meters between the
compressor and the work area.
•Any coloring of the belt guards of the compressor during painting
operations indicates that the distance is too short.
•Inserttheplugoftheelectriccableinasocketofsuitableshape,voltage
andfrequencycomplyingwithcurrentregulations.
•Use extension cables with a maximum length of 5 meters and of suitable
cross-section.
•The use of extension cables of different length and also of adapters and
multiple sockets should be avoided.
•Always use the switch of the pressure switch to switch off the compressor
•Always use the handle to move the compressor.
•Whenoperating, thecompressormustbeplacedona stable,horizontal
surface to guarantee correct lubrication.
GENERAL SAFETY INSTRUCTIONS
•Neverdirectthejetofairtowardspersons,animalsoryourbody.(Always
wear safety goggles to protect your eyes against flying objects that may be
liftedbythejetofair).
•Neverdirectthejetofliquidssprayedbytoolsconnectedtothecompressor
towards the compressor.
•Never use the appliance with bare feet or wet hands or feet.
•Never pull the power cable to disconnect the plug from the socket or to
move the compressor.
•Never leave the appliance exposed to adverse weather conditions.
•Never transport the compressor with the receiver under pressure.
•Donotweldormachinethereceiver.Inthecaseoffaultsorrusting,replace
the entire receiver.
•Never allow inexpert persons to use the compressor. Keep children and
animals at a distance from the work area.
• Thisapplianceisnotintendedforusebypersons(includingchildren)with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised toensure that they do notplaywith the
appliance.
•Donotpositionflammableornylon/fabricobjectsclosedtoand/oronthe
compressor.
•Nevercleanthecompressorwithflammableliquidsorsolvents.Checkthat
you have unplugged the compressor and clean with a damp cloth only.
•The compressor must be used only for air compression. Do not use the
compressor for any other type of gas.
•The compressed air produced by the compressor cannot not be used
for pharmaceutical, food or medical purposes except after particular
treatments and cannot be used to fill the air bottles of scuba divers.
OPERATION
• To avoid overheating of the electric motor, this compressor is designed
for intermittent operation as indicated on the technical dataplate (for
example, S3-25 means 2.5 minutes ON, 7.5 minutes OFF). In the case of
overheating, the thermal cutout of the motor trips, automatically cutting
off the power when the temperature is too high. The motor restarts
automatically when normal temperature conditions are restored.
•To facilitate restart of the compressor, in addition to the operations
indicated,itisimportanttoreturnthebuttonofthepressureswitchtothe
OFFpositionandthentoONagain(figures 1-2).
•Single-phaseversionsarefittedwith a pressure switch equippedwitha
delayedclosingairdischargevalvewhichfacilitatesstart-upofthemotor.
Therefore venting of air from this valve for a few seconds with the receiver
empty is normal.
•Allthecompressorsarettedwithasafetyvalvethatistrippedinthecase
of malfunctioning of the pressure switch in order to assure machine safety.
 Thesafetyvalveissettoavoidover-pressurizationoftheairtanks.This
valveisfactorypre-setandwillnotfunctionunlesstankpressurereaches
this pressure. Do not attempt to adjust or eliminate this safety device.
 Anyadjustmentstothisvalvecouldcauseseriousinjury.Ifthisdevicerequires
serviceormaintenance,seeanAuthorizedServiceCenter.
•The red notch on the pressure gauge refers to the maximum operating
pressure of the tank. It does not refer to the adjusted pressure.
•Whenttingatool,theowofairinoutputmustbeswitchedoff.
•Whenusingcompressedair,youmustknowandcomplywiththesafety
precautionstobeadoptedforeachtypeofapplication(ination,pneumatic
tools,painting,washingwithwater-baseddetergentsonly,etc.).
•Please check that the air consumption and the maximum working pressure of
thepneumatictoolandconnectionpipes(withthecompressor)tobeused,
are compatible with the pressure set on the pressure regulator and with the
amount of air supplied by the compressor.
•Supplyhosesatpressuresabove7barshouldbeequippedwithasafety
cable(e.g.awirerope).
ASSEMBLY
2
You must fully assemble the appliance before using it for the first time.
Fitting the wheels
Fit the supplied wheel kit as shown in fig. 3.Assemblybysequence:a,b,
c,d,e.
Fitting the rubber foot
Fit the supplied rubber stopper as shown in fig. 4.
Fitting the air filter
Remove the shipping plug with a screwdriver or similar and screw the air
filtersecurelytotheequipment(fig. 5).
Fitting the transport handle
Screw the transport handle to the compressor as shown in fig. 15.
VOLTAGE
3
Thecompressorisequippedwithamainscablewithshock-proofplug.This
canbeconnectedtoany230V~50Hzshock-proofsocketwhichisprotected
bya16Afuse.Beforeyouusethemachine,makesurethatthemainsvolt-
agecomplieswiththespecificationsontheratingplate.Longsupplycables,
extensions,cablereelsetc.causeadropinvoltageandcanimpedemotor
start-up.Inthecaseoflowtemperaturesbelow+5°C,motorstart-upisjeop-
ardized as a result of stiffness.
Connection of the mains plug (electrical information for the BS plug)
Important!
The wires in the mains lead fitted to this product are coloured in accordance
with the code shown in fig. 16.
● The 3 pin plug must comply to BS1363/A.
● Fuse must comply to BS1362.
Ifforanyreasonthe13ampplugfittedtothisproductrequiresreplacement
it must be wired in accordance with the following instruction:
Do not connect the brown (live) or blue (neutral) to the earth pin marked
‘E’ on the 3 pin plug.
Connect the Blue wire to the terminal marked Neutral (N). Connect the
BrownwiretotheterminalmarkedLive(L).ConnecttheYellow&Greenwire
totheterminalmarkedEarth(E).Ensurethattheouterinsulationisgripped
by the cord grip and that the wires are not trapped when replacing the plug
cover.Themainslead onthisproduct isfittedwith a13amp(BS1363/A)
plug.A13amp(BS1362)fusemustbefittedintheplug.
If in doubt consult a qualified electrician
There are no user serviceable parts inside this product except those referred
tointhemanual.Alwaysreferservicingtoqualifiedservicepersonnel.Never
removeanypartofthecasingunlessqualifiedtodoso;thisunitcontains
dangerous voltages.
Warning!
For your protection if this product is to be used outdoors it should not be
exposed to rain or used in damp locations. Do not place the product on damp
Preserve this handbook for future reference