ENGLISH (Original Instructions)
32
♦ Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular
cleaning.
♦ Regularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
♦ Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur
contact an authorised repair agent.
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be
regularly lubrication around the SDS Plus fitment.
Cleaning
WARNING! Blow dirt and dust out of the
main housing with dry air as often as dirt is
seen collecting in and around the air vents.
Wear approved eye protection and approved dust
mask when performing this procedure.
WARNING! Never use solvents or other
harsh chemicals for cleaning the non-
metallic parts of the tool. These chemicals may
weaken the material of the parts. Use only mild
soap and damp cloth to clean the tool. Never let any
liquid get inside the tool,cleaning of gasoline or
other chemicals, never immerse any part of the tool
into liquid.
LOWER GUARD
The lower guard should always rotate and close freely from
a fully open to fully closed position. Always check for correct
operation before cutting by fully opening the guard and
letting it close. If the guard closes slowly or not completely
it will need cleaning or servicing. Do not use the saw until it
functions correctly. To clean the guard, use dry air or a soft
brush to remove all accumulated sawdust or debris from the
path of the guard and from around the guard spring. Should
this not correct the problem, it will need to be serviced by an
authorized service center.
Blades
A dull blade will cause inefficient cutting, overload on
the saw motor, excessive splintering and increase the
possibility of kickback. Change blades when it is no longer
easy to push the saw through the cut, when the motor is
straining, or when excessive heat is built up in the blade.
It is a good practice to keep extra blades on hand so that
sharp blades are available for immediate use. Dull blades
can be sharpened in most areas.
Hardened gum on the blade can be removed with kerosene,
turpentine, or oven cleaner. Anti-stick coated blades
can be used in applications where excessive build- up is
encountered, such as pressure treated and green lumber.
OPTIONAL ACCESSORIES
WARNING! Since accessories, other than those
offered by Stanley, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only Stanley,
recommended accessories should be used with this
product.
Various types of SDS Plus drill bits and chisels are available
as an option.
Consult your dealer for further information on the
appropriate accessories.
Protecting The Environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Please sort it out for
separate recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Some local governments may require the local or municipal
waste disposal centers or retailers of new products to
provide households with electronic product recycling
services.
NOTES
Stanley’s policy is one of continuous improvement to our
products and as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations. All Stanley Service Centers
are staffed with trained personnel to provide customers
with efficient and reliable power tool service. For more
information about our authorized service centers and
if you need technical advice, repair, or genuine factory
replacement parts, contact the Stanley location nearest you.
To Next Page
Loading...
