dered inoperative. This can result in serious
injuries.
► Work only with an undamaged deflector.
► Work with a correctly installed line limiter
blade.
► If you have any queries: Contact your
STIHL servicing dealer.
4.6.3 Mowing Head
The mowing head is in a safe condition if the fol‐
lowing points are observed:
–
The mowing head is not damaged.
–
The mowing head is not jammed.
–
The mowing head is correctly installed and
firmly tightened.
–
The mowing lines are properly installed.
–
If a Polycut mowing head with polymer blades
is used:
–
The polymer blades are free of damage and
tears.
–
The polymer blades are properly mounted.
–
The wear limits are not exceeded.
WARNING
■ If they are in an unsafe condition, parts of the
mowing head, mowing lines or polymer blades
may come off and be ejected at high speed.
People may be seriously injured.
►
Work only with an undamaged mowing
head.
► If a PolyCut mowing head with polymer
blades is used: Never work with damaged
polymer blades.
►
Never use metal objects in place of the
nylon mowing lines or polymer blades.
► Observe and remain inside the wear limits.
► If you are unsure: Consult a STIHL author‐
ized dealer.
4.6.4 Metal cutting attachment
The metal cutting attachment is in a safe condi‐
tion if the following points are observed:
–
Metal cutting attachment and mounting hard‐
ware are undamaged.
–
The metal cutting attachment is not warped.
–
The metal cutting attachment is properly
installed and firmly tightened.
–
The metal cutting attachment is correctly
sharpened.
–
Cutting edges of the metal cutting attachment
have no burrs.
–
The wear limits are not exceeded.
–
If a metal cutting attachment not manufactured
by STIHL is used, it must not be heavier,
thicker, of a different shape, of a lower quality,
or larger in diameter than the largest metal
cutting attachment approved by STIHL.
WARNING
■
If it is not in an safe condition, parts of the
metal cutting attachment may come off and be
thrown at high speed. People may be seri‐
ously injured.
►
Never work with a damaged metal cutting
attachment or damaged mounting hard‐
ware.
►
Sharpen the metal cutting attachment cor‐
rectly.
► Deburr the cutting edges with a file.
► Have the metal cutting attachment bal‐
anced by a STIHL servicing dealer.
► Observe and remain inside the wear limits.
► Use a metal cutting attachment specified in
these instructions for use.
► If you are unsure: Consult a STIHL author‐
ized dealer.
4.6.5 Battery
The battery is in a safe condition if the following
points are observed:
–
Battery is undamaged.
–
The battery is clean and dry.
–
Battery functions properly and has not been
modified.
WARNING
■
A battery that is not in a safe condition cannot
operate safely. Persons may be seriously
injured.
►
Never work with a damaged battery.
► Never attempt to charge a damaged or
defective battery.
► If the battery is dirty: Clean the battery.
► If the battery is wet or damp: Allow the bat‐
tery to dry, 20.6.
► Never attempt to modify the battery.
► Never insert objects in the battery’s open‐
ings.
► Never bridge the battery's contacts with
metallic objects (short circuit).
► Do not open the battery.
► Replace worn or damaged labels.
■ Fluid may leak from a damaged battery. If that
liquid comes into contact with the skin or eyes,
the skin or eyes may be irritated.
►
Avoid contact with the liquid.
► If skin contact occurs: Wash affected areas
of skin with plenty of water and soap.
► In the event of contact with eyes: Rinse
eyes with plenty of water for at least
15 minutes and consult a doctor.
English 4 Safety Precautions
8 0458-027-0101-A
To Next Page
Loading...
Need help?
General
