Supermicro SUPERO X10DRW-i - 2-8 Connecting Cables

Chapter 2: Installation
2-27
S-SGPIO
I-SGPIO2
I-SGPIO1
JIPMB1
SAN MAC
IPMI CODE
JBAT1
JPWR1
S-SATA1
S-SATA0
S-SATA3 S-SATA2
I-SATA1
I-SATA0
I-SATA3
I-SATA2
I-SATA4
I-SATA5
BIOS
LICENSE
JPI2C1
JPWR2
JPWR3
JF1
JL1
JSTBY1
JTPM1
JVRM2
JVRM1
JPME2
JVR1
JWD1
JPG1
JPB1
JI2C1
JI2C2
JPL1
SP1
LED1
LEDM1
JBT1
FANB
FANA
FAN4
FAN3
FAN2
USB4/5(3.0)
AOM CPU1 PCI-E 3.0 X16
CPU1
CPU2
P2-DIMMG1
P2-DIMMH1
P2-DIMMG2
P2-DIMMH2
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMD2
P1-DIMMC1
P1-DIMMC2
P1-DIMMD1
P2-DIMMF2 P2-DIMMF1 P2-DIMME2
P2-DIMME1
SXB1C
SXB1B:CPU1 PCI-E 3.0 X16 + CPU2 PCI-E 3.0 X16
UID-SW
LAN2
LAN1
USB2/3(3.0)
USB0/1(3.0)
IPMI_LAN
VGA
COM1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
IPMI
Flash
BIOS
SXB2:CPU2PCI-E 3.0 X16
SXB1A
LAN
X10DRW-i(T)
Rev. 1.01
PCH
CTRL
LED2
BMC
P1-DIMMB2
FAN1
J35
Warning: To provide adequate power supply
to the motherboard, be sure to connect the
24-pin ATX power (JPWR1), and the two
8-pin power connectors (JPWR2, JPWR3) to
the power supply. Failure to do so may void
the manufacturer warranty on your power
supply and motherboard.
2-8 Connecting Cables
Power Connectors
A 24-pin main power supply connector
(JPWR1), and two 8-pin CPU power con-
nectors (JPWR2/JPWR3) are located on
the motherboard. These power connec-
tors meet the SSI EPS 12V specication
and must be connected to your power
supply to provide adequate power to the
system. See the tables on the right for pin
denitions.
A. J24: 24-pin ATX PWR
(Req'd)
B. JPWR1: 8-pin Proces-
sor PWR (Req'd)
C. JPWR2: 8-pin Proces-
sor PWR (Req'd)
A
B
C
ATX Power 24-pin Connector
Pin Denitions (JPW1)
Pin# Denition Pin # Denition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
(Required)
12V 8-pin Power Connec-
tor Pin Denitions
Pins Denition
1 through 4 Ground
5 through 8 +12V