Supermicro SUPERO X10DRW-i - S-SGPIO;I-SGPIO Headers and Standby Power

Chapter 2: Installation
2-31
S-SGPIO
I-SGPIO2
I-SGPIO1
JIPMB1
SAN MAC
IPMI CODE
JBAT1
JPWR1
S-SATA1
S-SATA0
S-SATA3 S-SATA2
I-SATA1
I-SATA0
I-SATA3
I-SATA2
I-SATA4
I-SATA5
BIOS
LICENSE
JPI2C1
JPWR2
JPWR3
JF1
JL1
JSTBY1
JTPM1
JVRM2
JVRM1
JPME2
JVR1
JWD1
JPG1
JPB1
JI2C1
JI2C2
JPL1
SP1
LED1
LEDM1
JBT1
FANB
FANA
FAN4
FAN3
FAN2
USB4/5(3.0)
AOM CPU1 PCI-E 3.0 X16
CPU1
CPU2
P2-DIMMG1
P2-DIMMH1
P2-DIMMG2
P2-DIMMH2
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMD2
P1-DIMMC1
P1-DIMMC2
P1-DIMMD1
P2-DIMMF2 P2-DIMMF1 P2-DIMME2
P2-DIMME1
SXB1C
SXB1B:CPU1 PCI-E 3.0 X16 + CPU2 PCI-E 3.0 X16
UID-SW
LAN2
LAN1
USB2/3(3.0)
USB0/1(3.0)
IPMI_LAN
VGA
COM1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
IPMI
Flash
BIOS
SXB2:CPU2PCI-E 3.0 X16
SXB1A
LAN
X10DRW-i(T)
Rev. 1.01
PCH
CTRL
LED2
BMC
P1-DIMMB2
FAN1
J35
A. I-SGPIO 1 (for I-SATA0-3)
B. I-SGPIO 2 (for I-SATA4/5)
C. SGPIO
D. Standby PWR
S-SGPIO and I-SGPIO 1/2 Headers
Three SGPIO (Serial Link General
Purpose Input/Output) headers are
located on the motherboard. I-SGPIO
1 supports I-SATA 0-3, and I-SGPIO 2
supports I-SATA 4/5. S-SGPIO is used
for S-SATA 0-3. All SATA ports support
SATA 3.0. See the table on the right
for pin denitions.
Note: NC= No Connection
S-SGPIO & I-SGPIO 1/2 Headers
Pin Denitions
Pin# Denition Pin Denition
1 NC 2 NC
3 Ground 4 Data
5 Load 6 Ground
7 Clock 8 NC
Standby Power Header
The +5V Standby Power header is
located at JSTBY1 on the mother-
board. See the table on the right for
pin denitions. (You must also have a
card with a Standby Power connector
and a cable to use this feature.)
Standby PWR
Pin Denitions
Pin# Denition
1 +5V Standby
2 Ground
3 No Connection
C
D
A
B