Supermicro SUPERO X10DRW-i - 2-9 Jumper Settings

Chapter 2: Installation
2-33
S-SGPIO
I-SGPIO2
I-SGPIO1
JIPMB1
SAN MAC
IPMI CODE
JBAT1
JPWR1
S-SATA1
S-SATA0
S-SATA3 S-SATA2
I-SATA1
I-SATA0
I-SATA3
I-SATA2
I-SATA4
I-SATA5
BIOS
LICENSE
JPI2C1
JPWR2
JPWR3
JF1
JL1
JSTBY1
JTPM1
JVRM2
JVRM1
JPME2
JVR1
JWD1
JPG1
JPB1
JI2C1
JI2C2
JPL1
SP1
LED1
LEDM1
JBT1
FANB
FANA
FAN4
FAN3
FAN2
USB4/5(3.0)
AOM CPU1 PCI-E 3.0 X16
CPU1
CPU2
P2-DIMMG1
P2-DIMMH1
P2-DIMMG2
P2-DIMMH2
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMD2
P1-DIMMC1
P1-DIMMC2
P1-DIMMD1
P2-DIMMF2 P2-DIMMF1 P2-DIMME2
P2-DIMME1
SXB1C
SXB1B:CPU1 PCI-E 3.0 X16 + CPU2 PCI-E 3.0 X16
UID-SW
LAN2
LAN1
USB2/3(3.0)
USB0/1(3.0)
IPMI_LAN
VGA
COM1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
IPMI
Flash
BIOS
SXB2:CPU2PCI-E 3.0 X16
SXB1A
LAN
X10DRW-i(T)
Rev. 1.01
PCH
CTRL
LED2
BMC
P1-DIMMB2
FAN1
J35
2-9 Jumper Settings
Explanation of Jumpers
To modify the operation of the mother-
board, jumpers can be used to choose
between optional settings. Jumpers create
shorts between two pins to change the
function of the connector. Pin 1 is identied
with a square solder pad on the printed
circuit board. See the motherboard layout
pages for jumper locations.
Note: On two pin jumpers,
"Closed" means the jumper is
on and "Open" means the jumper
is off the pins.
Connector
Pins
Jumper
Cap
Setting
Pin 1-2 short
3 2 1
3 2 1
LAN Enable/Disable
JPL1 enables or disables Gigabit_LAN
ports 1/2 on the X10DRW-i, and 10G_
LAN ports 1/2 on the X10DRW-iT. See
the table on the right for jumper settings.
The default setting is Enabled.
LAN Enable
Jumper Settings
Jumper Setting Denition
1-2 Enabled (default)
2-3 Disabled
A
A. GLAN1/2 Enable
(X10DRW-i)
A. 10G_LAN1/2 En-
able (X10DRW-iT)