SP91 User Manual
[Particularize] · When select cancel user-defined character set, automatically select inner character
set.
· n only valid at least significant bit.
[Default] n = 0
[Reference] ESC
ESC
ESC
ESC &
&
&
& , ESC
ESC
ESC
ESC ?
?
?
?
ESC
ESC
ESC
ESC &
&
&
& y
y
y
y c1
c1
c1
c1 c2
c2
c2
c2 [x1
[x1
[x1
[x1 d1...d(y
d1...d(y
d1...d(y
d1...d(y ×
×
×
× x1)]...[xk
x1)]...[xk
x1)]...[xk
x1)]...[xk d1...d(y
d1...d(y
d1...d(y
d1...d(y ×
×
×
× xk)]
xk)]
xk)]
xk)]
[Name] Define user-defined characters
[Format] ASCII ESC & y c1 c2 [x1 d1...d(y × x1)]...[xk d1...d(y × xk)]
Hex 1B 26 y c1 c2 [x1 d1...d(y × x1)]...[xk d1...d(y × xk)]
Decimal 27 38 y c1 c2 [x1 d1...d(y × x1)]...[xk d1...d(y × xk)]
[Range] y = 3
32 ≤ c1 ≤ c2 ≤ 126
0
≤
x
≤
12 (when font A (12
×
24) is selected)
0 ≤ x ≤ 9 (when font B (9 × 17) is selected)
0 ≤ d1...d(y × xk) ≤ 255
[Description] Define user-defined characters.
· y specifies the number of bytes in the vertical direction.
· c1 specifies the beginning character code for the definition, and c2 specifiesthefinal
code.
· x specifies the number of dots in the horizontal direction.
[Particularize] · Characters code can be defined: ASCII from <20>H to <7E>H (95 characters).
· The continued characters code of several characters can be undefined. When only
need one character, so c1 = c2
。
· d is the dot data of characters. Dot mode is from the left in horizontal direction. The
right left dots are blank.
· Define the data of user-defined character is (y × x) bytes.
· Set the relevant of printing dot is 1 or 0 which is the relevant of do not printing the
dots.
· Define the different user-defined character mode for each character type by this
command. Set the character type by ESC
ESC
ESC
ESC !
!
!
! or ESC
ESC
ESC
ESC M
M
M
M .
· User-defined character and download bit image can not define at the same time.
When executing this command, download bit image will be cleared.
· Under the following situations, user-defined characters will be cleared:
① Execute ESC
ESC
ESC
ESC @
@
@
@ .
② Execute GS
GS
GS
GS *
*
*
* .
③ Execute ESC
ESC
ESC
ESC ?
?
?
? .
④ The printer reset or turn the power off.
· When the user-defined characters defines in character typeB (9 ´ 17), only effect
to the highest valuable bit of the third byte in the vertical direction data.
[Default] Inner character font
[Reference] ESC
ESC
ESC
ESC
%
%
%
%
, ESC
ESC
ESC
ESC ?
?
?
?
[For example]
· When setting the character type A (12 × 24).
To Next Page
Loading...