EasyManuals Logo

Taylor 750 Operator's Manual

Taylor 750
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image
OPERATING PROCEDURES
6-9
Models 750, 751, 754, 774, 791, and 794
Operating Procedures
6
Closing Procedure
To disassemble your machine, the following items will be
needed:
Two cleaning pails
Sanitized stainless-steel rerun can with lid
Necessary brushes (provided with freezer)
Cleaner
Single-service towels
Draining Product from the Freezing
Cylinder
1. Press the AUTO button, canceling compressor and
beater motor operation.
Press the MIX refrigeration button, canceling the mix
hopper refrigeration system.
2. Remove the hopper cover, hopper gasket, and air
tube. Take these parts to the sink for cleaning.
3. If local health codes permit the use of rerun, place
a sanitized, NSF-approved stainless-steel rerun
container beneath the door spout. Press the WASH
button and lower the draw handle. Drain the
remaining product from the freezing cylinder and mix
hopper. When the flow of product stops, press the
WASH button and raise the draw handle. Place the
sanitized lid on the rerun container and place it in the
walk-in cooler.
Note: If local health codes do not permit the use
of rerun, the product must be discarded. Drain the
product into a pail and properly discard it.
4. Repeat step 1 through step 3 for the other side of
the freezer on Models 754, 774, 791, and 794.
Rinsing
1. Pour 2 gal. (7.6 L) of cool clean water into the mix
hopper. With the brushes provided, scrub the mix
hopper, mix inlet hole and mix-level sensing probe.
2. With a pail beneath the door spout, raise the prime
plug and press the WASH button.
3. When a steady stream of rinse water is flowing from
the prime plug opening in the bottom of the freezer
door, lower the draw handle. Drain all the rinse water
from the freezing cylinder, raise the draw handle and
press the WASH button canceling the Wash mode.
4. Repeat step 1 through step 3 for the other side of
the freezer on models 754, 774, 791, and 794.
Cleaning
Note: Use warm water and follow the manufacturer's
specifications.
1. Prepare an approved 100 ppm cleaning solution
(examples: 2.5 gal. [9.5 L] of Kay-5
®
or 2 gal.
[7.6 L] of Stera-Sheen
®
).
2. Push down the prime plug. Pour the cleaning solution
into the mix hopper.
3. While the solution is flowing into the freezing cylinder,
brush-clean the mix hopper, mix-level sensing probe,
and the mix inlet hole.
4. Press the WASH button. This will cause the cleaning
solution in the freezing cylinder to agitate.
5. Place an empty pail beneath the door spout and raise
the prime plug.
6. When a steady stream of cleaning solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all of
the solution.
7. Once the cleaner stops flowing from the door spout,
raise the draw handle and press the WASH button
canceling the Wash mode.
8. Repeat step 1 through step 7 for the other side of
the freezer on Models 754, 774, 791, and 794.
Disassembly
WARNING! Make sure the power switch is in
the OFF position! Failure to follow this instruction may
result in severe personal injury to fingers or hands from
hazardous moving parts.
1. Remove the handscrews, freezer door(s), beater(s),
scraper blades, and driveshaft(s) from the freezing
cylinder(s). Take these parts to the sink for cleaning.
2. Remove the front drip tray and the splash shield.
ALWAYS FOLLOW LOCAL HEALTH CODES.

Other manuals for Taylor 750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Taylor 750 and is the answer not in the manual?

Taylor 750 Specifications

General IconGeneral
BrandTaylor
Model750
CategoryFreezer
LanguageEnglish

Related product manuals