EasyManuals Logo

TC Electronic SYSTEM 6000 MKII User Manual

TC Electronic SYSTEM 6000 MKII
68 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
8
dsp 6000 - Card and COnneCTIOns
Use the supplied cable to connect the AES/EBU Inputs/
Outputs.
Cable type is twisted pair (12 pairs) with common screen.
Recommended impedance: 110 Ohm.
2QHHQGLVHTXLSSHGZLWKDQ$(6(%8SLQ'6XE
FRQQHFWRUWKHRWKHUHQGLVHTXLSSHGZLWKIRXUPDOH;/5¶V
DQGIRXUIHPDOH;/5¶V
0DOH;/5¶VDUHPDUNHGZLWK2XWWR
)HPDOH;/5¶VDUHPDUNHGZLWK,1WR
Extension cables must be constructed according to AES/
(%8VWDQGDUGV
Following is the pin-out:
Cable pair
3LQQXPEHU QXPEHU ;/5 ;/5SLQ $VVLJQPHQW
1 1a Female 1 2 Input 1/2 +
2 2a Female 2 2 Input 3/4 +
3 3a Female 3 2 Input 5/6 +
4 4a Female 4 2 Input 7/8 +
5 5a Male 1 2 Output 1/2 +
6 6a Male 2 2 Output 3/4 +
7 7a Male 3 2 Output 5/6 +
8 8a Male 4 2 Output 7/8 +
9 No connection No connection
10 9a Female 1 1 Common
11 No connection No connection
12 9b Female 2 1 Common
13 10a Female 3 1 Common
13 10b Female 4 1 Common
14 1b Female 1 3 Input 1/2 -
15 2b Female 2 3 Input 3/4 -
16 3b Female 3 3 Input 5/6 -
17 4b Female 4 3 Input 7/8 -
18 5b Male 1 3 Output 1/2 -
19 6b Male 2 3 Output 3/4 -
20 7b Male 3 3 Output 5/6 -
21 8b Male 4 3 Output 7/8 -
22 11a Male 1 1 Common
23 11b Male 2 1 Common
24 12a Male 3 1 Common
24 12b Male 4 1 Common
25 Shield no connection Common
Note: Twisted cable pairs must be respected
Sync In Word Clock
)RUFRQQHFWLRQVWRH[WHUQDOFORFNYLDWKHVWDQGDUG%1&
connector (see illustration above).
When several devices are connected in a chain and
synced via Word Clock, termination on the last device of
the chain is necessary.
As the System 6000 is expected to be the last unit in such
a chain (or the only), the factory default setting on the
System 6000 DSP card is: TERMINATED (75 Ohm).
If you need to terminate the Word Clock signal elsewhere
in the chain you will need to un-terminate the System 6000
DSP card. To do this you must remove the DSP card from
the mainframe and remove the termination jumper:
 6ZLWFKRIIWKHSRZHUDQGGLVFRQQHFWPDLQSRZHUFRUG
 /RRVHQWKHWZRVFUHZVKROGLQJWKH'63FDUGDQG
remove the card gently.
 5HPRYHWKHWHUPLQDWLQJMXPSHUQHDUWKH%1&SOXJ
 ,QVHUWWKHFDUGJHQWO\LQWKH'63VORWDQGUHPRXQW
the screws.
Pins connected via jumper : Terminated (75 Ohm).
Pins NOT connected via jumper : Not Terminated
Termination jumper
'LSVZLWFKHVWRVKRXOG$/:$<6EHVHWWRRII
General Handling
When inserting or removing any modules, avoid touching
the circuit board by handling only the rear panel of the
module. To minimize the static potentials that can cause
damage to the electronic circuits, you should observe
precautionary grounding techniques such as touching a
grounded System 6000 Mainframe immediately before
inserting modules.
BNC
connector

Other manuals for TC Electronic SYSTEM 6000 MKII

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TC Electronic SYSTEM 6000 MKII and is the answer not in the manual?

TC Electronic SYSTEM 6000 MKII Specifications

General IconGeneral
BrandTC Electronic
ModelSYSTEM 6000 MKII
CategoryComputer Hardware
LanguageEnglish

Related product manuals