What to do if my TechniSat DIGIPLUS UHD S Tuner has no image, no sound, and the display is not illuminated?
If your TechniSat Tuner displays no image, no sound, and the display is not illuminated, the cause may be a lack of mains voltage. To resolve this, check the power supply.
How to fix a TechniSat DIGIPLUS UHD S Tuner remote control that is not working?
If your TechniSat Tuner remote control isn't working, it might be due to an incorrect remote control code. Try setting the correct remote control code. Also, check if the batteries are spent and replace them if necessary.
Why is there no picture via HDMI on my TechniSat DIGIPLUS UHD S Tuner?
If you are not getting a picture via HDMI on your TechniSat Tuner, it may be due to the set HDMI resolution not being supported. Try adjusting the HDMI resolution.
What to do if the picture on my TechniSat DIGIPLUS UHD S is incomplete or distorted?
If your TechniSat Tuner is showing an incomplete or distorted picture, the issue might be with the picture format settings. Check the picture format. It could also be related to the picture display or zoom settings; check the picture display or zoom in the menu and zoom settings.
Why is there no sound or incorrect sound on my TechniSat DIGIPLUS UHD S?
If you are experiencing no sound or incorrect sound with your TechniSat Tuner, it could be because Dolby Digital is active or an incorrect audio language is selected. Check the settings in the menu, specifically Dolby Digital and language selection.
What to do if my TechniSat DIGIPLUS UHD S Tuner has no image, no sound, but the display is illuminated?
If your TechniSat Tuner has no image and no sound, but the display is illuminated, the problem may be a short-circuit in the LNB connection. In this case, switch off the device, rectify the short-circuit, and then switch the device back on. Alternatively, there may be a defective or missing cable connection, so check all cable settings. A faulty LNB or incorrect outdoor unit setting on the receiver could also be the cause; replace the LNB or modify the setting accordingly.
Why is my TechniSat Tuner not receiving channels that were OK before?
If your TechniSat Tuner is not receiving channels that were previously working, the dish may be incorrectly positioned or faulty. Check the dish. It's also possible that the channel is being transmitted on another transponder; in this case, perform a search/scan. It's also possible that the channel is no longer being transmitted.
How to display channels missing from the TechniSat DIGIPLUS UHD S channel list?
If you find that various channels are not showing up in the channel list on your TechniSat Tuner, the cause may be that an incorrect channel list is selected. To solve this, select another channel list.
Why does my TechniSat DIGIPLUS UHD S Tuner picture have square blocks or show "no signal"?
If your TechniSat Tuner's picture sometimes has square blocks, freezes, or shows a black screen with a "no signal" message, it may be due to heavy rain or snow. Remove snow from the dish. The dish may also be incorrectly aligned, so re-align it. If the dish is too small for the reception location, use a larger dish. Also, check for any obstacles between the dish and the satellite, such as a tree, and mount the dish in an unobstructed position.
Why can't I rotate the antenna on my TechniSat DIGIPLUS UHD S?
If the antenna of your TechniSat Tuner cannot be rotated, it may be because the motor is not suitable for DiSEqC 1.2. Use a suitable dish.
Explains warning and information symbols used in the manual.
How to connect the device to a television via HDMI.
Methods for choosing TV or radio channels.
Records programmes using the DVR function.
Accesses and plays recorded content.
General| Certification | CE |
|---|---|
| Package depth | 195 mm |
| Package width | 310 mm |
| Package height | 80 mm |
| Package weight | 1350 g |
| Operating temperature (T-T) | 5 - 35 °C |
| Operating relative humidity (H-H) | 10 - 75 % |
| Timer | Yes |
| Tuner type | Digital |
| Demodulation | 8PSK, QPSK |
| Product color | Black |
| Interactive TV | - |
| Frequency range | 950 - 2150 MHz |
| Number of tuners | 2 tuner(s) |
| Audio output channels | - channels |
| On Screen Display (OSD) languages | CZE, DEU, DUT, ENG, ESP, FRE, GRE, HUN, ITA, POL, POR, RUS, SWE, TUR |
| Digital Satellite Equipment Control (DiSEqC) | 1.0, 1.2 |
| Signal source | Satellite |
| Supported video modes | 576i, 576p, 720p, 1080i, 1080p, 2160p |
| Digital signal format system | DVB-S, DVB-S2 |
| Audio formats supported | AAC, AIFF, FLAC, M4A, MP2, MP3, WAV |
| Image formats supported | BMP, GIF, JPEG, PNG |
| Video formats supported | ASF, AVI, M2TS, MKV, MOV, MP4, MPG, MTS, TS, TS4, VOB |
| Video compression formats | AVC, H.264, H.265, HEVC, MPEG1, MPEG2 |
| Display type | LCD |
| Ethernet LAN data rates | 1000 Mbit/s |
| AC input voltage | 230 V |
| Power consumption | 400 mA |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.4 W |
| Power consumption (typical) | 17.1 W |
| USB 2.0 ports quantity | 2 |
| USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity | 0 |
| Built-in HDD | No |
Weight and Dimensions| Depth | 175 mm |
|---|---|
| Width | 220 mm |
| Height | 40 mm |
| Weight | 668 g |
To Next Page
