Teka CML 45 - Changing Coffee Temperature

110
English
When “DESCALE” is displayed, the machine re-
quires descaling.
Proceed as follows:
• Makesuretheapplianceisreadyandthewater
softener filter has been removed.
• PresstheMENUbutton(B6)thenpresstheNEXT
button (B7) repeatedly until the appliance dis-
plays“DESCALENO”.
• PresstheCHANGEbutton(B8)andtheappliance
displays“DESCALEYES”.
• Press the OK button (B9) to start the descale
programme.
• Emptythewatertank,pourthecontentsofthe
descaler bottle into the tank respecting the in-
structions given on the descaler pack, then add
wateruptotheMAXlevelmarkedonthewater
tank.
When descaling subsequently, use descaler of
the same type and brand as supplied (available
from the manufacturer’s authorised Customer
Services) or a descaler recommended by Cus-
tomer Services. Always follow the instructions
on the pack.
• Attachthecappuccinomakertothenozzle.
• Placeacontainerwith aminimumcapacity of
1.5 litres under the cappuccino maker (fig. 3).
• PresstheOKbutton.Descalerowsoutofthe
cappuccino maker into the container below.
“APPLIANCEINDESCALE”isdisplayed.
• Thedescaleprogrammeautomaticallyperforms
a series of deliveries and pauses to remove lim-
escale deposits from inside the machine.
• Afterabout30minutes,theappliancedisplays
“RINSINGFILLTANK”.
The appliance must now be rinsed through to
eliminate residues of descaling solution from
inside the appliance.
Proceed as follows:
• Emptythewatertank,rinseandllwithclean
water.
• Replacethetank;
• Emptythefullcontainerandputbackunderthe
cappuccino maker.
• PresstheOKbutton.Hotwaterowsoutofthe
cappuccino maker spout into the container be-
lowandtheappliancedisplays“RINSING”.
• When the water tank is empty, the appliance
displays the message “RINSING COMPLETE...
PRESSOK”.
• Press the OK button and rell the water tank
with clean water.
• Thedescaleprogrammeisnowterminatedand
the appliance is ready to make coffee again.
NOTE:Ifdescalingisinterruptedbeforecomple-
tion, the machine still displays the descaling
message and the process must be begun again
from the beginning.
Empty the water tank, rinse with clean water
and deliver a cup of hot water.
Important! FAILURE TO DESCALE THE
APPLIANCE REGULARLY INVALIDATES THE
GUARANTEE.
Changing coffee temperature
To change coffee temperature, proceed as follows:
• Press the MENU button (B6), then press the
NEXTbutton(B7)repeatedlyuntiltheappliance
displays“TEMPERATUREHIGH...”.
• Press the CHANGE button (B8) until the appli-
ance displays the required coffee temperature.
• PresstheOKbutton(B9)toconrm.
• Press the MENU button to exit programming
modeorNEXTtochangeotherparameters.
Changing the length of time the
appliance remains on
The appliance is set by default to go off automati-
cally 1 hour after the last coffee has been made.
To increase the number of hours the machine stays
on (max. 3), proceed as follows:
• PresstheMENUbutton(B6)thenpresstheNEXT
button (B7) repeatedly until the appliance dis-
plays:“OFFAFTER1HOUR”.
• Press the CHANGE button (B8) to change the
number of hours the appliance remains on.
• PresstheOKbutton(B9)toconrm.
• Press the MENU button to exit programming
modeorNEXTtochangeotherparameters.