Tektronix MSO70000C/DX

To Next Page

To Previous Page

Install your ins

trument

DPO7000C models

1. Turn off power

2. Connect secon

d monitor.

3. Connect key

board.

4. Connect mou

se.

5. Turn on in

strument power.

6. Turn on mo

nitor power.

DPO7000C Series

MSO/DPO70000DX, MSO/DPO70000C, DP O7000C, and MS O/DPO5000 Series U ser M anual 13

Main Page

Table of Contents7
Important Safety Information11
General Safety Summary11
Service Safety Summary13
Terms in this Manual14
Symbols and Terms on the Product14
Compliance Information15
EMC Compliance15
Safety Compliance16
Environmental Considerations19
Preface20
Key Features20
Documentation22
Conventions Used in this Manual22
Install Your Instrument23
Standard Accessories23
Operating Requirements25
Preventing ESD28
Powering on the Instrument29
Powering off the Instrument31
Removing the Power32
Securing the Oscilloscope33
Connecting to a Network33
Adding a Second Monitor34
Operating System Restore37
Installing the MSO5000 and DPO5000 Hard Drive38
Getting Acquainted with Your Instrument39
Front Panel39
Side and Rear Panels42
Interface and Display45
Control Panel47
Accessing Online Help50
Accessing Menus and Control Windows51
Inspect Your Instrument52
Verify Internal Diagnostics Pass52
Acquisition53
Signal Path Compensation53
Setting up Analog Signal Input55
Using Default Setup57
Using Autoset58
Probe Compensation and Deskew59
Acquisition Concepts59
How the Acquisition Modes Work62
Changing the Acquisition Mode63
Starting and Stopping an Acquisition64
Selecting the Horizontal Mode64
Using Fastacq67
Using DSP Enhanced Bandwidth68
Setting the Termination Voltage70
Using Roll Mode71
Setting up Digital Signal Input72
Setting up Digital Channels73
Setting up a Bus75
When and Why to Turn on Magnivu80
Using Magnivu80
Viewing Analog Characteristics of Digital Waveforms81
Using Fastframe Mode83
Using Fastframe Frame Finder86
Pinpoint Triggers88
Triggering Concepts88
Choosing a Trigger Type90
Trigger Selections92
Checking Trigger Status94
Using a (Main) and B (Delayed) Triggers95
Triggering with B-Event Scan98
Triggering on a Parallel Bus100
Triggering on a Serial Bus102
Triggering Using Visual Triggers (Visual Triggering)103
Setting up Action on Event105
Sending E-Mail on Trigger106
Setting up E-Mail on Event107
Using Horizontal Delay109
Display a Waveform110
Setting the Display Style110
Setting the Display Persistence111
Setting the Display Format112
Selecting the Waveform Interpolation113
Adding Screen Text114
Setting the Graticule Style115
Setting the Trigger Level Marker116
Displaying the Date and Time116
Using the Color Palettes117
Setting Reference Waveform Colors118
Setting Math Waveform Colors118
Using Multiview Zoom118
Zooming in Multiple Areas120
Lock and Scroll Zoomed Waveforms122
Hide Waveforms in the Zoomed Window123
Using Wave Inspector to Manage Long Record Length Waveforms124
Searching and Marking Waveforms126
Using a Visual Search134
Analyzing Waveforms135
Taking Automatic Measurements135
Automated Measurement Selections137
Customizing an Automatic Measurement140
Taking Cursor Measurements144
Setting up a Histogram146
Using Math Waveforms148
Using Spectral Analysis151
Using the Serial Error Detector154
Using Mask Testing160
Using Limit Testing163
Myscope165
Creating a New Myscope Control Window165
Using Myscope Control Windows169
Saving and Recalling Information171
Saving Screen Captures171
Saving Waveforms172
Recalling Waveforms174
Saving Digital Waveforms175
Saving Instrument Setups176
Recalling Instrument Setups177
Saving Measurements178
Saving User Masks179
Saving Histogram Data180
Saving Timestamps181
Copying Your Results to the Clipboard182
Printing a Hard Copy184
Run Application Software185
Application Examples187
Capturing Intermittent Anomalies187
Using the Extended Desktop and Openchoice Architecture for Efficient Documentation190
Triggering on Buses192
Triggering on a Video Signal193
Correlating Data between a Tektronix Oscilloscope and Logic Analyzer195
Cleaning196
Obtaining the Latest Oscilloscope Application and Version Releases197
TPP0500 and TPP1000 500 Mhz and 1 Ghz 10X Passive Probes Instructions198
Operating Information198
Connecting the Probe to the Oscilloscope198
Compensating the Probe199
Standard Accessories199
Optional Accessories201
Replacing the Probe Tip201
Specifications201
Performance Graphs202
Safety Summary203
P6616 General-Purpose Logic Probe Instructions205
Product Description205
Connecting the Probe to the Oscilloscope206
Connecting the Probe to Your Circuit207
Functional Check207
Typical Application208
Accessories208
Specifications209
Safety Summary210
Safety Terms and Symbols in this Manual210
Contacting Tektronix211
Warranty Information211
Index213

Tektronix MSO70000C/DX

Table of Contents

Other manuals for Tektronix MSO70000C/DX

Related product manuals