What to do if hopper door partially or completely open on Tennant Scrubber?
If the hopper door is partially or completely open, causing poor sweeping performance in your Tennant Scrubber, close the hopper door.
What to do if Thermo Sentry tripped in Tennant Scrubber?
If the Thermo Sentry has tripped, resulting in excessive dusting in your Tennant Scrubber, reset the Thermo Sentry.
What to do if fabric prescreen missing on dust filters of Tennant Scrubber?
If the fabric prescreen is missing on the dust filters, leading to excessive dusting in your Tennant Scrubber, clean the filter elements and install the fabric prescreen.
How to reduce excessive dusting from my Tennant 800 Floor Machine?
Excessive dusting from your Tennant Floor Machine can be due to several reasons. The brush skirts and dust seals may be worn, damaged, or out of adjustment, requiring replacement or adjustment. The hopper dust filter might be clogged; try shaking, cleaning, or replacing it. Ensure the main brush is operating in Normal speed, not II Speed. A damaged vacuum hose or vacuum fan seal could also be the cause, needing replacement. Check if the hopper door is partially or completely closed and open it. Reset the Thermo Sentry if it has tripped. Clean filter elements and install a fabric prescreen if it’s missing on the dust filters. If the vacuum fan has failed, contact TENNANT service personnel.
Why is my Tennant Blower causing excessive dusting?
Excessive dusting from your Tennant Blower can occur for several reasons. The brush skirts and dust seals may be worn, damaged, or improperly adjusted—in which case, you should replace or adjust them. The hopper dust filter might be clogged, requiring you to shake, clean, or replace it. Ensure the main brush operates at Normal speed, not II Speed. Check for a damaged vacuum hose and replace it if necessary. Inspect the vacuum fan seal; if damaged, replace it. Also, ensure the hopper door is fully open and that the fabric prescreen is installed on dust filters, cleaning the filter elements if needed. Finally, reset the Thermo Sentry if it has tripped.
What to do if my Tennant Blower vacuum fan fails, causing excessive dusting?
If the vacuum fan on your Tennant Blower fails, resulting in excessive dusting, contact TENNANT service personnel.
General| Brand | Tennant |
|---|---|
| Model | 800 |
| Category | Floor Machine |
| Language | English |
Essential safety guidelines for operating and servicing the machine.
Procedures for safely moving the machine by pushing, towing, or transporting it.
Instructions on how to properly jack up and store the machine.
Detailed technical specifications including dimensions, capacities, and performance metrics.
Scheduled maintenance tasks for Gas/LPG and Diesel engines.
Details on standard bolt torque charts, metric and SAE grades, and identification.
Information on removing, replacing, and adjusting the operator's seat assembly.
Details on service brakes, replacement of brake shoes, and adjustment procedures.
Instructions for adjusting both foot-activated and hand-activated parking brakes.
Procedures for repacking front wheel bearings and servicing rear tires and wheels.
Explanation of the RFS option for filter cleaning and its operational requirements.
Procedures for removing, installing, and adjusting the debris hopper and dump door.
Details on servicing the hopper dust filter and replacing the Thermo Sentry.
Steps for replacing, checking, and adjusting the main brush pattern and bearings.
Procedures for replacing and adjusting the side brush tip angle and ride height.
Information on replacing and adjusting brush compartment and rear skirts.
Guidelines for cleaning, checking, and replacing the machine's battery.
Procedures for replacing, disassembling, and reassembling the instrument panel.
Instructions for locating and replacing machine relays and circuit breakers.
Wiring diagrams and schematics for various machine systems and engine types.
Steps for draining, filling, and maintaining the hydraulic fluid reservoir and filter.
Details on the directional pedal, cable, and control adjustment procedures.
Procedures for replacing major hydraulic components like pumps, cylinders, and motors.
Step-by-step instructions for replacing the vacuum fan hydraulic motor.
Guidance on diagnosing and resolving hydraulic system issues through flow charts.
Procedures for removing and installing the Ford 2.3 Liter engine.
Maintenance guidelines for engine oil, cooling system, and fan belts.
Servicing the air filter system and gasoline/LPG fuel systems.
Information on governor actuators, troubleshooting, and ignition system maintenance.
Procedures for replacing engine starter and alternator.
Troubleshooting common issues related to the LPG fuel system.
Procedures for removing and installing the Perkins 200 Series engine.
Maintenance guidelines for engine oil, cooling system, and radiator.
Steps for servicing the air filter indicator and replacing the air filter element.
Details on diesel fuel system components, filters, and priming procedures.
Instructions for priming the diesel fuel system after maintenance.
Procedures for replacing engine starter and alternator.
Procedures for removing and installing the Perkins 700 Series engine.
Maintenance guidelines for engine oil, cooling system, and radiator.
Steps for servicing the air filter indicator and replacing the air filter element.
Details on diesel fuel system components, filters, and priming procedures.
Instructions for priming the diesel fuel system after maintenance.
Procedures for replacing engine starter and alternator.
To Next Page
