Tennant 5280 - User Manual

Other manuals for Tennant 5280

Use And Care Guide2 pages

Operator And Parts Manual68 pages

Questions and Answers

E
Erika TaylorAug 18, 2025
What to do if Tennant Floor Machine ES option will not operate?
- M
  Mr. Victor ReedAug 18, 2025
  If the ES option on your Tennant Floor Machine isn't working, it could be due to several reasons. First, check if the ES ON/OFF switch is activated. If not, turn it on. Another possible cause is a clogged ES filter; remove and clean it. Also, the ES float switch might be clogged, so rinse it off. In case of a faulty ES pump or float switch, or a faulty ES ON/OFF switch, further assistance is needed.
L
Lori BeckerAug 21, 2025
Why is my Tennant Floor Machine leaving water behind?
- G
  grossvalerieAug 21, 2025
  If the Tennant Floor Machine exhibits poor water pickup, several factors could be at play. The recovery tank might be full or filled with foam, in which case, empty it. The float shut-off screen inside the recovery tank, the squeegee, or the vacuum hose could be clogged; clean them accordingly. Worn squeegee blades or a damaged vacuum hose should be replaced. Ensure vacuum hose connections are firm and that the recovery tank inlet hole is free of obstructions. Also, check the recovery tank cover and drain hose plug are correctly positioned and tightened, and replace the gasket on the recovery tank cover if it's worn. Lastly, ensure the machine has sufficient battery charge.
U
urussellAug 25, 2025
What to do if the brush motor of Tennant Floor Machine won't operate?
- J
  James SantiagoAug 26, 2025
  If the brush motor on your Tennant Floor Machine won't operate, there are several potential reasons. The control grips may not be rotated, so rotate them. The brush circuit breaker might have tripped, so replace the pad or adjust the pad pressure and reset the brush circuit breaker button.
B
Brandon MossAug 28, 2025
What to do if the vacuum motor of Tennant Floor Machine won't operate?
- D
  david11Aug 28, 2025
  If the vacuum motor on your Tennant Floor Machine isn't operating, it could be due to several reasons. The squeegee might be raised off the floor, so lower it. The main circuit breaker or the vacuum motor circuit breaker might have tripped, so remove any obstruction and reset the corresponding circuit breaker button.
E
erichendersonAug 30, 2025
How to fix little to no solution flow in Tennant Floor Machine?
- E
  Elizabeth ThompsonAug 31, 2025
  If there's little to no solution flow in your Tennant Floor Machine, first ensure the solution switch is on and the control grips are rotated. A clogged solution line or solution tank filter could be the issue; remove the hose and blow compressed air through it, and flush the solution tank after each use. Also, a clogged solution valve or solenoid might be the problem; remove and clean them, being careful not to scratch the inside of the valve. The solution flow knob may not be activated, so turn it on. If the set screw on the solution knob is loose, calibrate the knob and tighten the screw. Finally, a broken solution control cable may be the cause, so replace the cable.
E
Eric BrownSep 2, 2025
Why does my Tennant 5280 Floor Machine have a short run time?
- A
  Alyssa PhillipsSep 3, 2025
  A short run time in your Tennant Floor Machine can be caused by batteries that are not fully charged, so charge them. Other potential causes include defective batteries (replace the battery), batteries needing maintenance, a faulty charger (repair or replace the battery charger), or excessive brush/pad pressure (properly adjust the pressure).
A
Amanda WolfeSep 5, 2025
Why won't my Tennant Floor Machine turn on?
- C
  clewisSep 5, 2025
  If your Tennant Floor Machine isn't operating, several things could be the cause. A faulty machine power switch might be the culprit and you should contact the service center. Also, the batteries may need charging, or the batteries themselves could be faulty and need replacement. Check for a loose battery cable and tighten it if necessary. Finally, the MAIN circuit breaker might have tripped, so determine the cause and reset the breaker.
F
fthompsonSep 8, 2025
How to improve scrubbing performance of Tennant Floor Machine?
- A
  Alejandra JohnsonSep 8, 2025
  If the Tennant Floor Machine has poor scrubbing performance, consider these potential causes: the brush/pad may be worn or incorrect, so replace it. Debris might be caught in the brush/pad, so remove it. The brush motor circuit breaker could be tripped, so reset it. A low battery charge can also cause this issue, so charge the batteries. Lastly, the brush/pad pressure may be incorrect, so readjust it.
K
Kathleen HernandezSep 12, 2025
Why is the ES option not working on my Tennant Floor Machine?
- B
  Brian GutierrezSep 12, 2025
  If the ES option on your Tennant Floor Machine isn't working, make sure the ES ON/OFF switch is activated. Also, the ES filter might be clogged, so remove and clean it. The ES float switch could be clogged, so rinse it off.
R
rivasjenniferNov 15, 2025
Why is the Tennant 5280 Floor Machine not picking up water well?
- W
  William MorrisNov 15, 2025
  Poor water pickup in your Tennant Floor Machine can occur due to several reasons: the recovery tank might be full or filling with foam, the float shut-off screen or squeegee could be clogged, the squeegee blades might be worn, vacuum hose connections could be loose, the vacuum hose could be clogged or damaged, the recovery tank inlet hole might be obstructed, the gasket on the recovery tank cover could be worn, the drain hose plug could be loose, the recovery tank cover might not be in place, or the battery charge level might be low. To resolve this, empty the recovery tank, clean the screen and squeegee, replace worn blades or the gasket, ensure tight hose connections, clear any hose obstructions, replace damaged hoses, clear the inlet hole, tighten the plug, properly position the cover, ...