Programming the Control Panel Premier 48, 88, 168 & 640 Installation Manual
88 INS176
User Config.
This menu will only be displayed if a Custom User type is
selected AND ‘User Menu’ (User Option: U) is enabled (see
page 87 for details).
This menu defines which menu options are available to the user
when their code is entered.
Press
to scroll through the options and press
to
select them or use keys
-
(‘Letter’ = option IS
selected, ‘Star’ = option is NOT selected).
The following options are available:
C - Change Code
The selected user can change their own User code.
Z - Chime Zones
The selected user can access the ‘Edit Chime Zones’ option,
allowing them to select which zones chime when activated.
T - Change Timers
The selected user can access the ‘Override Timers’, ‘Alter
Timers’, ‘Alter Part Arms’, ‘Alter Hol. Dates’ and ‘Edit Phone
No.’ menu options.
S - System Tests
The selected user can access the ‘System Tests’ option,
allowing them to walk test zones, activate the external
sounder etc..
U - Setup Users
The selected user can access the ‘Setup Users’ option,
allowing them to alter existing users or assign new users.
However, users cannot assign User types to the system that
have a higher access level than themselves. Also, if a user
assigns a Custom User type, functions that are not available
to them cannot be assigned to the Custom user.
E - Eng. Access
The selected user can access the ‘Enable Engineer’ option,
allowing them to authorise Engineer access or Remote UDL
access to the system.
A - Add Eng. Code (Engineers only)
Only Available to Engineers.
N - NVM Locking (Engineers only)
Only Available to Engineers.
User Time Lock
This option allows the selected user to be denied access to
the system at different times of the day and days of the week.
When a Control Timer is assigned to a user, the User code
will not allow access to any functions during the timer ‘On’
period (see page 52 for timer programming).
The first 4 options (Premier 48) or 6 options (Premier
88/168/640) will lockout the selected user (Code and TAG)
when the corresponding control timer is active. The last two
options will lock out the selected users TAG (T) when Custom
Output 2 Stage A is active or lock out the selected users
Code (C) when Custom Output 2 Stage B is active.
This allows conditions to be set up in the custom outputs and
then the TAG or Code to be locked out during those
conditions i.e. Custom Output 2 Stage B could be
programmed to activate during entry, resulting in the code
being disabled during the entry period.
User Name Text
Each user can be assigned up to 8 characters of name text.
This can be beneficial when reading the log, as identification
of people is made easier.
See page 34 for details on programming text.
Text is programmed in a similar way to mobile phones. Select
characters by pressing the corresponding key the
appropriate number of times (to select a character on the
same key, press the
key to move the cursor along).
Door Control
This option would normally be used for access control as it
only allows the user to open/unlock doors that are assigned
to that user code.
Door control is only available to users with the ‘Door
Strike’ attribute assigned to it.
Deleting Users
If a User code needs to be deleted from the system, this must
be done, by a user that has access to the ‘Setup Users’
menu.
To delete User codes proceed as follows:
Ensure that Setup Users is selected, the display should
look like this:
,6,24+11,
"12-0"/0G
Press
, the display should look like this:
"12-0"/0
+1"/0"/XX
Select a user from 1 to 24 (Premier 48), 1 to 49
(Premier 88) or 1 to 99 (Premier 168)
then
press
, the display should look like this:
+1"/0"/,!"F
XXXXXX
Press
, the display will look something like this:
,6,24+11,
0"/9=
Where ‘15’ is the selected User number.
Press
to confirm deletion of the selected User code
Press
to exit from Setup Users
To Next Page
Loading...
