What to do if Thermo Scientific Laboratory Equipment displays 'Flow meter data version mismatch'?
If the firmware installed in the module does not support the full functionality of the flow meter, you should update the firmware.
What to do if Thermo Scientific Dionex UltiMate 3000 displays 'Flow meter (x) inlet filter or capillary clogged'?
If the filter frit of the inline filter in the ProFlow flow meter is clogged, replace the filter frit.
What does it mean if Thermo Scientific Dionex UltiMate 3000 could not deliver desired flow for more than 30 seconds?
If the internal limit for the primary pressure has been reached and the set flow rate could not be delivered for a longer period, batch processing will be aborted.
What to do if Thermo Scientific Dionex UltiMate 3000 Laboratory Equipment displays 'Chip card x data inconsistent'?
If the data on the chip card (column ID) are inconsistent, verify that the chip card is installed properly. If necessary, use a new chip card, as the current one may be defective.
What to do if Thermo Scientific Dionex UltiMate 3000 Laboratory Equipment autozero flow failed?
If autozero flow failed because the drift was too high, wait until the module is equilibrated and repeat the autozero.
What to do if Thermo Scientific Laboratory Equipment displays '(x) counts deviation in zero position'?
Turn the module off and on again by pressing the power switch on the rear of the module. If the message appears more often, contact Service.
What to do if Thermo Scientific Dionex UltiMate 3000 displays 'Zero position not found during the last revolution'?
Turn the module off and on again by pressing the power switch on the rear of the module.
General| Type | HPLC System |
|---|---|
| Data Sampling Rate | up to 100 Hz |
| Pump Type | Quaternary, binary |
| Flow Rate Range | 0.001 to 10 mL/min |
| Detection Methods | UV-Vis, Fluorescence, Electrochemical, MS |
| Temperature Control | Yes, with column oven |
| Sample Capacity | Varies by autosampler model |
| pH Range | 1 to 14 |
| Injection Volume | 0.1 to 100 µL |
| Detection Wavelength Range | 190 to 800 nm |
| Autosampler Capacity | Varies by model, up to several hundred samples |
| Dimensions (H x W x D) | Varies by module |
| Weight | Varies by configuration |
| Power Requirements | 100 - 240 VAC, 50/60 Hz |
Details symbols, precautions, and warnings for safe operation and handling of chemical solvents and the HPLC system.
Details key features: Rear Seal Wash, Flow Meter, Leak Sensor, Purge Valve, Inline Filter.
Explains how to control the module using the Chromeleon Chromatography Management System.
Covers features for monitoring module health, performance, and diagnostics.
Lists requirements for the installation site, including access, stability, and environmental conditions.
Covers loading USB drivers, installing, and configuring the module within Chromeleon.
Details rear seal wash setup, flow meter settings, and pump purging procedures.
Explains the process of equilibrating the UltiMate 3000 system before sample analysis.
Describes module power-up sequence, internal tests, and status indicators.
Guides on connecting, direct control, and automated control via Chromeleon.
Covers solvent selection, flow/pressure limits, purging, leak detection, and degasser operation.
Details temperature control, column ID, sensor sensitivity, and screen adjustments.
Covers predictive performance, diagnostics, digital I/O, and qualification functions.
Provides best practices for achieving optimal system stability and reproducibility.
Lists precautions for interrupting operation or preparing the module for shipping.
Details general maintenance, intervals, and calibration procedures for optimal performance.
Introduces features for identifying and eliminating operational problems.
Lists module-related messages and their corresponding remedial actions.
Lists common operating problems, their probable causes, and suggested remedial actions.
Covers general service notes, safety precautions, and procedures for user-performed maintenance.
To Next Page