EasyManuals Logo

Thytronic NC20 User Manual

Thytronic NC20
227 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
14
14
NC2 0 - Manual - 01 - 2015
TECHNICAL DATA
3.2 INPUT CIRCUITS
Auxiliary power supply Uaux
Voltage
Nominal value (range) 24...48 V~/-
115...230 V~/110...220 V-
Operative range (each one of the above nominal values) 19...60 V~/-
85...265 V~/75...300 V-
Inrush current (max)
24 V- 6 A, 5 ms
48 V- 14 A, 5 ms
110 V- 20 A, 1 ms
230 V~ 50 A, 1 ms
Frequency (for alternate voltage supply) 45...66 Hz
Max distortion factor ( for alternating voltage supply) 15%
Max alternating component (for dc voltage supply):
Full wave rectifi ed sine wave 100 %
Sine wave 80 %
Power consumption:
Maximum (energized relays, Ethernet TX) 10 W (20 VA)
Maximum (energized relays, Ethernet FX) 15 W (25 VA)
Phase current input circuits
Relay nominal phase current I
n
1 A or 5 A selectable by dip-switch
Permanent overload 25 A
Thermal overload (1 s) 500 A
Dynamic overload (half cycle) 1250 A
Rated consumption (for any phase) 0.002 VA with I
n
=1 A
0.04 VA with I
n
=5 A
Unbalance neutral current input circuit
Relay nominal unbalance nominal current I
Nn
1 A or 5 A selectable by dip-switch
Permanent overload 25 A
Thermal overload (1 s) 500 A
Dynamic overload (half cycle) 1250 A
Rated consumption 0.006 VA with I
En
=1 A
0.12 VA with I
En
=5 A
Voltage input circuits
Relay nominal voltage U
n
50...130 V (U
R
= 100 V)
Permanent overload 1.3 U
R
Thermal overload (1 s) 2 U
R
Rated consumption (for any phase) ≤ 0.5 VA
Binary input circuits
Quantity 2
Type optocoupler
Operative range 24...265 V~/-
Min activation voltage U
DIGmin
18 V
Max consumption, energized I
DIG
3 mA
3.3 OUTPUT CIRCUITS
Relays
Quantity 6
Type of contacts K1, K2 changeover (SPDT, type C)
Type of contacts K3, K4, K5 make (SPST-NO, type A)
Type of contacts K6 break (SPST-NC, type B)
Nominal current 8 A
Nominal voltage/max switching voltage 250 V~/400 V~
Breaking capacity:
Direct current (L/R = 40 ms) 50 W
Alternating current (λ = 0,4) 1250 VA
Make 1000 W/VA
Short duration current (0,5 s) 30 A
Minimum switching load 300 mW (5 V/ 5 mA)
Life:
Mechanical 10
6
operations
Electrical 10
5
operations
Block output (Logic selectivity)
Quantity 1
Type optocoupler

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Thytronic NC20 and is the answer not in the manual?

Thytronic NC20 Specifications

General IconGeneral
BrandThytronic
ModelNC20
CategoryPower distribution unit
LanguageEnglish

Related product manuals