TM 9-1829A - Page 6

TM 9-1829A, April 1944 6/100 2021-07-07
Figure 112:Tapping pointer on staff while running on calibrating machine (T-170645) ..................................... 75
Figure 113: Waltham speedometer, disassembled ................................................................................................ 76
Figure 114: Speedometer mechanism (dial removed) .......................................................................................... 77
Figure 115: Speedometer mechanism (odometers removed) ................................................................................ 77
Figure 116: Frame, second gear and magnet assembly ........................................................................................ 78
Figure 117: Loosening bonnet adjusting screws with calibration adjuster (STS-10878) ..................................... 79
Figure 118: Stewart-Warner hour meter and mileage recorder ............................................................................ 80
Figure 119: Stewart-Warner recorder, disassembled ............................................................................................ 80
Figure 120: Recorder with cover removed ........................................................................................................... 81
Figure 121: Removing sleeve retaining pin .......................................................................................................... 81
Figure 122: Driving out sleeves ............................................................................................................................ 82
Figure 123: Pressing sleeves into case .................................................................................................................. 82
Figure 124: Flexible shaft ..................................................................................................................................... 83
Figure 125: Drawing showing length to cut core stock ........................................................................................ 83
Figure 126: Cutting core stock, using fixture (T-136374) .................................................................................... 84
Figure 127: Squaring end of inner core, using fixture (T-136374) ....................................................................... 85
Figure 128: Crimping tip on inner core, using fixture (T-136374) ....................................................................... 85
Figure 129: Drawing showing length to cut casing stock ..................................................................................... 86
Figure 130: Crimping ferrule, using fixture (T-52644) ........................................................................................ 86
Figure 131: Ferrule crimped on casing ................................................................................................................. 86
Figure 132: Crimping ferrule, using pliers (T-122308) ........................................................................................ 87
Figure 133: Lubricating inner core as it is assembled to casing ........................................................................... 87
Figure 134: AC heavy-duty speed adapter ........................................................................................................... 88
Figure 135: AC heavy-duty speed adapter, disassembled .................................................................................... 88
Figure 136: Stewart-warner type 666 drive joint .................................................................................................. 89
Figure 137: Stewart-Warner type 666 drive joint, disassembled .......................................................................... 89
Figure 138: Removing gear (A), using adapter tool (T-178708 Det. 4) ............................................................... 90
Figure 139: Driving out sleeve retaining pin ........................................................................................................ 90
Figure 140: Driving out sleeve ............................................................................................................................. 90
Figure 141: Removing gear (D), using adapter tool (T-178708 Det. 3) ............................................................... 91
Figure 142: Pressing gears off shaft, using adapter tool (T-178708 Det. 1) ......................................................... 91
Figure 143: Pressing gear (C), on shaft, using adapter tool (T-178708 Det. 1) .................................................... 92
Figure 144: Dimensional drawing of intermediate gears assembled on shaft ....................................................... 92
Figure 145: Pressing sleeve into case ................................................................................................................... 92
Figure 146: Pressing gear (D), on shaft, using adapter tool (T-178708 Det. 1 and 5) .......................................... 93
Figure 147: Pressing sleeve (transmission end) into case, using adapter tool (T-178708 Det. 3) ........................ 93
Figure 148: Pressing gear (A) on shaft, using adapter tool (T-178708 Det. 1 and 3) ........................................... 93
Figure 149: Stewart-Warner 659 Distributor-type drive joint .............................................................................. 94
Figure 150: Stewart-Warner 659-type drive joint, partially disassembled ........................................................... 94
Figure 151: Master tool kit (T-187852) ................................................................................................................ 95
Figure 152: Calibrating machine and Accessories (T-170645); magnet strengt testers and hair spring kit (408082)
.............................................................................................................................................................................. 96
Figure 153: Special tools ...................................................................................................................................... 97
Figure 154: Special tools ...................................................................................................................................... 97
Figure 155: Calibrating machine (T-170645) with speedometer mounted on spindle no. 1 ready for test ........... 98
Figure 156: Demagnetizing, using special tool (846294) while operating speedometer on calibrating machine (T-
170645) ................................................................................................................................................................. 99
Digitalized by 45manuals@gmail.com, https://45manuals.wixsite.com/manuals for free distribution