Toro 03676 - Page 9

To Next Page

To Previous Page

decal136-3721

136-3721

1.ReadtheOperator’s

Manualforlubrication

information.

6.Engineairlter

11.Enginecoolant16.Fluids

2.Brakefunctions

7.Engineoil12.Engineoillevel

17.Capacity

3.Checkevery8hours.

8.Fanbelt13.Fuel

18.Fluidinterval(hours)

4.Hydraulicuid

9.Battery

14.ReadtheOperator’s

Manual.

19.Filterinterval(hours)

5.Tirepressure10.Radiatorscreen

15.Fuel/Waterseparator

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup10
Preparing the Machine10
Adjusting the Control-Arm Position11
Installing the Cutting Units11
Using the Cutting-Unit Kickstand19
Installing the CE Hood Lock20
Applying the CE Decals21
Product Overview22
Controls22
Seat Controls24
Using the Menus25
Specifications28
Attachments/Accessories28
Before Operation29
Before Operation Safety29
Fuel Specification29
Fuel Tank Capacity30
Adding Fuel30
Performing Daily Maintenance30
Checking the Interlock Switches30
During Operation31
During Operation Safety31
Starting the Engine32
Hydraulic Filter-Restriction Indicator32
Shutting off the Engine32
Adjusting the Turf-Compensation Spring32
Adjusting the Lift-Arm Counterbalance33
Adjusting the Lift-Arm Turnaround Position33
Setting the Reel Speed34
Understanding the Diagnostic Light35
Operating Tips35
After Operation36
After Operation Safety36
Tie-Down Point Locations36
Hauling the Machine36
Pushing or Towing the Machine36
Maintenance38
Maintenance Safety38
Recommended Maintenance Schedule(S)38
Daily Maintenance Checklist40
Pre-Maintenance Procedures41
Preparing for Maintenance41
Opening the Hood41
Closing the Hood41
Opening the Screen41
Closing the Screen42
Tilting the Seat42
Lowering the Seat42
Jacking Point Locations43
Lubrication43
Greasing the Bearings and Bushings43
Engine Maintenance45
Engine Safety45
Checking the Air Filter45
Servicing the Air Cleaner45
Resetting the Air Filter Service Indicator46
Oil Specification46
Checking the Level of the Engine Oil46
Crankcase Oil Capacity47
Changing the Engine Oil and Filter47
Fuel System Maintenance48
Draining Water from the Fuel-Water Separator48
Replacing the Water-Separator Filter48
Bleeding the Fuel System49
Checking the Fuel Lines and Connections49
Draining the Fuel Tank49
Cleaning the Fuel-Pickup Tube Screen49
Close and Latch the Hood; Refer to Closing the Hood49
Service Interval: Every 250 Hours49
Electrical System Maintenance52
Electrical System Safety52
Disconnecting the Battery52
Connecting the Battery53
Charging the Battery53
Servicing the Battery53
Replacing a Fuse-Block Fuse53
Replacing the Telematic Fuse54
Replacing the TEC Controller Fuse54
Drive System Maintenance55
Checking the Tire Air Pressure55
Checking the Torque of the Wheel Nuts55
Adjusting the Traction Drive for Neutral55
Checking the Rear-Wheel Alignment56
Adjusting the Rear Wheel Toe-In56
Cooling System Maintenance57
Cooling System Safety57
Coolant Specification57
Checking the Coolant Level58
Removing Debris from the Cooling System58
Brake Maintenance59
Adjusting the Parking Brakes59
Prepare the Machine; Refer to Preparing for Maintenance59
Adjusting the Parking-Brake Latch60
Figure 10960
Belt Maintenance61
Tensioning the Alternator Belt61
Open the Hood; Refer to Opening the Hood61
Close and Latch the Hood; Refer to Closing the Hood61
Hydraulic System Maintenance62
Hydraulic System Safety62
Hydraulic Fluid Specifications62
Checking the Hydraulic-Fluid Level62
Checking the Hydraulic Lines and Hoses63
Replacing the Hydraulic Filters63
Hydraulic Fluid Capacity64
Changing the Hydraulic Fluid64
Cutting Unit System Maintenance65
Blade Safety65
Checking the Reel-To-Bedknife Contact65
Backlapping the Cutting Units65

Toro 03676 - Page 9

Table of Contents

Related product manuals