Toro 30602 - Lubrication; Greasing the Bearings and Bushings

To Next Page

To Previous Page

Lubrication

GreasingtheBearingsand

Bushings

Themachinehasgreasettingsthatmustbelubricated

regularlywithNo.2GeneralPurposeLithiumBaseGrease.

Ifthemachineisoperatedundernormalconditions,lubricate

allbearingsandbushingsafterevery50hoursofoperationor

immediatelyaftereverywashing.

Thegreasettinglocationsandquantitiesare:

TractionUnit

ServiceInterval:Every50hours

•Brakepedalpivotshaftbearings(2)(Figure37)

•Frontandrearaxlepivotbushings(2)(

Figure38)

•Steeringcylinderballjoints(2)(Figure39)

•Tierodballjoints(2)(Figure39)

•Kingpinbushings(2)(Figure39).

Thetopttingonthekingpinshouldonlybe

lubricatedannually(2pumps).

Figure37

Figure38

Figure39

CenterCuttingUnit

Note:Deckmayhavetoberaisedtoexposethegrease

ttingsforthelatchpivotandthelowerlink.

Latchpivot(2)(Figure41)

Note:Thelatch(

Figure40)mayneedtobemanuallytripped

togainaccesstothegreasetting.Useaprybartocloseand

re-openthelatch

Figure40

1.Latch

Main Page

Introduction2
Table of Contents3
Safety4
Safe Operating Practices4
Toro Mower Safety6
Sound Power Level6
Sound Pressure Level-Model 306027
Sound Pressure Level-Model 306047
Vibration Level7
Engine Emission Certification7
Safety and Instructional Decals8
Setup15
Greasing the Machine15
Replacing the Warning Decal15
Product Overview16
Controls16
Fore and Aft Adjusting Lever17
Seat Arm Rest Adjusting Knob17
Seat Back Adjusting Lever17
Weight Gauge17
Weight Adjusting Lever17
Wind Shield Wiper Switch17
Air Conditioning Switch17
Fan Control17
Temperature Control17
Wind Shield Latch18
Rear Window Latch18
Accessing the Protected Menu Settings21
To Set the Auto Idle21
To Set the Maximum Allowed Mow Speed21
To Set the Maximum Allowed Transport Speed21
Specifications22
Attachments/Accessories22
Operation23
Before Operating23
Adjusting the Mirrors31
Aiming the Headlights31
Starting and Stopping the Engine31
Smart Power32
Reversing Fan Operation32
Auto Idle32
Mow Speed32
Transport Speed32
Checking the Interlock Switches32
Using the Rollover Protection System (ROPS)33
Pushing or Towing the Machine33
Jacking Points34
Tie Downs34
Operating Characteristics34
Operating Tips34
Maintenance36
Recommended Maintenance Schedule(S)36
Service Interval Chart37
Lubrication38
Greasing the Bearings and Bushings38
Engine Maintenance40
Air Cleaner Maintenance40
Servicing the Engine Oil and Filter41
Fuel System Maintenance42
Servicing the Fuel System42
Servicing the Water Separator42
Electrical System Maintenance43
Battery Care43
Fuses44
Drive System Maintenance45
Adjusting the Traction Pedal Angle45
Changing the Planetary Gear Drive Oil45
Changing the Rear Axle Lubricant46
Checking the Rear Wheel Toe-In46
Changing the Front Tires46
Cooling System Maintenance47
Servicing the Engine Cooling System47
Brake Maintenance47
Adjusting the Service Brakes47
Belt Maintenance48
Servicing the Alternator Belt48
Servicing the Compressor Belt48
Re-Tensioning the Blade Drive Belts49
Replacing the Blade Drive Belt49
Hydraulic System Maintenance50
Changing the Hydraulic Fluid50
Replacing the Hydraulic Filters50
Checking the Hydraulic Lines and Hoses51
Adjusting the Counterbalance Pressure51
Mower Maintenance52
Pivoting (Tilting) the Front Cutting Unit Upright52
Pivoting the Front Cutting Unit down52
Adjusting the Cutting Unit Pitch52
Servicing the Castor Arm Bushings53
Servicing the Castor Wheels and Bearings53
Replacing the Cutting Unit Hinge Covers54
Blade Maintenance55
Checking for a Bent Blade55
Removing and Installing the Cutter Blade(S)55
Inspecting and Sharpening the Cutter Blade(S)55
Correcting Cutting Unit Mismatch56
Cab Maintenance57
Cleaning the Cab Air Filters57
Cleaning the Air Conditioning Coil58
Cleaning the A/C Condenser Screen58
Storage59
Preparing for Seasonal Storage59
Schematics60

Toro 30602 - Lubrication; Greasing the Bearings and Bushings

Table of Contents

Related product manuals