How to fix a Toro 41163 when the starter does not crank?
If the starter on your Toro Paint Sprayer isn't cranking, make sure to press the brake pedal and shift the range selector to the Neutral position. Also, check the electrical connections to ensure they have good contact. Verify and, if necessary, replace the fuse. Finally, ensure the battery is adequately charged; if not, charge or replace it.
What should I do if a boom section on my Toro Sprayer does not spray?
If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
Why is the distance reading inaccurate on my Toro 41163 Paint Sprayer?
If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
Why Toro 41163 starter does not crank?
The starter of your Toro Paint Sprayer might not be cranking due to several reasons: * The range selector might not be in Neutral—press the brake pedal and move the range selector to the Neutral position. * The electrical connections could be corroded or loose—check the electrical connections. * A fuse might be blown or loose—correct or replace the fuse. * The battery could be discharged—charge or replace the battery. * The safety interlock system might be malfunctioning—contact your Authorized Service Dealer. * There might be a broken starter or starter solenoid—contact your Authorized Service Dealer. * The internal engine components could be seized—contact your Authorized Service Dealer.
Why is the speed reading always 0 or erratic on my Toro 41163 Paint Sprayer?
If the speed reading on your Toro Paint Sprayer is always 0 or erratic, it could be due to: * A loose monitor cable. Connect the monitor cable. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
Why is the speed always 0 or erratic on my Toro Sprayer?
If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
What to do if Toro Paint Sprayer engine cranks, but will not start?
If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
What to do if Toro Paint Sprayer displayed measurements do not make sense?
If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
What does “OFL” mean on my Toro 41163 Paint Sprayer monitor?
If the monitor reads “OFL” on your Toro Paint Sprayer, it means the data has exceeded the maximum allowed. Press and hold the [Reset] button to clear the monitor.
Why does the monitor display 6553.5 in the Application Rate setting on my Toro 41163?
If the monitor displays 6553.5 when in the Application Rate setting on your Toro Paint Sprayer, contact your Authorized Service Dealer, because the monitor is not receiving data from the speed sensor.
General| Max Pressure | 3000 PSI |
|---|---|
| Hose Length | 25 ft |
| Power Source | Electric |
| Spray Pattern | Adjustable |
| Voltage | 120V |
| Type | Airless |
| Nozzle Size | 0.015 in |
To Next Page
