Toro 41163 User Manual (English)

Questions and Answers:

D
Debbie BrownSep 10, 2025
Why is my Toro 41163 Paint Sprayer engine losing power?
- S
  Steven YoungSep 10, 2025
  Your Toro Paint Sprayer engine might be losing power due to: * Incorrect crankcase oil level. Adjust it to the full mark. * A dirty air cleaner element. Clean or replace it. * Dirt, water, or stale fuel in the fuel system. Drain and flush the system, then add fresh fuel. * Engine overheating. Refer to the 'Engine Overheats' section. * A damaged or dirty spark plug. Replace it. * A plugged vent hole in the fuel tank vent fitting. Replace the fuel cap. * Low compression. Contact your Authorized Service Dealer.
C
Cynthia Moss DVMSep 1, 2025
What does it mean if the monitor of my Toro Sprayer reads 'OFL'?
- R
  Richard CohenSep 1, 2025
  If the monitor of your Toro Sprayer reads 'OFL', the data has exceeded the maximum allowed. Press and hold the [Reset] button to clear the monitor.
H
hoconnorAug 25, 2025
What to do if Toro 41163 area is inaccurate?
- J
  Judy GibsonAug 25, 2025
  If the area measurement on your Toro Paint Sprayer is inaccurate, check and set the appropriate width in the calibration mode. Also, calibrate the speed sensor.
K
Kevin TaylorAug 25, 2025
What to do if Toro Paint Sprayer monitor does not display Application Rate or Total Volume?
- J
  janespearsAug 25, 2025
  If the monitor on your Toro Paint Sprayer does not display the Application Rate or Total Volume, connect the monitor cable if it's loose. Clean the flow meter if it's dirty or clogged. Calibrate the flow meter.
D
David BrownAug 25, 2025
What to do if Toro Paint Sprayer Total Volume is inaccurate?
- E
  Edward Nolan DDSAug 26, 2025
  If the total volume on your Toro Paint Sprayer is inaccurate, clean the flow meter if it's dirty or clogged. Calibrate the flow meter.
S
Shawn WilliamsAug 26, 2025
Why is the area measurement inaccurate on my Toro 41163 Paint Sprayer?
- R
  Randall RogersAug 26, 2025
  The area measurement on your Toro Paint Sprayer could be inaccurate because: * The sprayer width is not correctly entered. Check and set the appropriate Width in the calibration mode. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
B
Brittney EvansAug 26, 2025
What causes inaccurate distance readings on my Toro 41163?
- K
  Kathy FischerAug 26, 2025
  Inaccurate distance readings on your Toro Paint Sprayer may be due to: * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
J
Jay DelacruzAug 26, 2025
Why is the total volume measurement inaccurate on my Toro 41163?
- P
  Peter RaymondAug 26, 2025
  The total volume measurement on your Toro Paint Sprayer can be inaccurate if: * The flow meter is dirty or clogged. Clean the flow meter. * The flow meter is not calibrated correctly. Calibrate the flow meter. * The flow meter is damaged. Contact your Authorized Service Dealer.
R
Rodney MurrayAug 26, 2025
Why is the total volume inaccurate on my Toro 41163 Paint Sprayer?
- J
  Janet VasquezAug 26, 2025
  If the total volume measurement is inaccurate on your Toro Paint Sprayer, clean the flow meter and calibrate the flowmeter.
A
andersonamyAug 27, 2025
What causes the area measurement to be inaccurate on my Toro Paint Sprayer?
- C
  Christopher LynchAug 27, 2025
  If the area measurement is inaccurate on your Toro Paint Sprayer, check and set the appropriate Width in the calibration mode and calibrate the speed sensor.